esp32 3d printed case

The case fits this board: https://github.com/Freenove/Freenove_ESP32_WROVER_BoardOne m5 nut or bolt is needed if you want to mount the case to something. ...I printed the case in PETG.You have access to all pins and micro usb port as well as the wifi...

Two hinged cases for the esp32 version of the wemos d1 mini. One of them has hexa pattern ventilation holes on the top cover and one is full. ... Ideal for use cases where the gpio pins are not used.

This is a project of ESP32-CAM case for Flsun Q5 3d printer. Parts required for assembly: - 2x M4x8mm screw (could be 10mm too) - 3x M3 nylon nut - 1x M3 nylon spacer 6mm - ESP32-CAM...

......Unfortunately, my first design had a stability problem on other DIN hat rails. This should be fixed with v1.1.For my ESP32 (38-pin with screw holes), which I want to use as a Bluetooth proxy in Home Assistant, I designed this ESP32 top hat rail case.

This version of the ESP32 Camera case works with the USB C version of the ESP32 camera module and might also be helpful with the micro USB version if the plugs are especially large. I have also removed the pesky downskin fillets and replaced them...

For some reason my wiring position of the ESP32 board was a bit different so I made a custom back cover case. I also made the lip height longer, just so it fits more firmly. ...

This is a case for the AI-On-The-Edge project to read out the watermeter with a ESP32 Cam. This case is made to fit with ANDRAE (see the picture) watermeter. The diameter of the watermeter is 65mm. The cap has a bayonet closure. ...The case based of...

Case for the Olimex POE powered ESP32 dev board. The lid have holes for airflow and snaps onto the case. You need to insert the board into the case by tilting it with the backside lowered, and than sliding it in. ...Than slide the other direction to...

Attention!! ...This case for a narrow board with a non-standard width of 25.5mm I strongly advise you not to buy such a fee. But if you have already purchased it, here is the case for you. ESP32 DevKit case v2

This is the design of a case to house an ESP32-CAM board along with a INMP441 microphone, a charge controller, and a 18650 cell. The case is held together by two M3x12 screws. This is a remix of glytchtech's case. ...The idea is to have a portable...

Despite having thousands of variants of ESP32 available on the market, I haven't found any case for the pico kit anywhere, so I made my own.It has integrated buttons in top part of the case, accessible pin headers at the bottom and hole for USB...

ESP32 Capacitive Touch Screen Module Case [ESP32-3248S035C]

Case for a TTGO ESP32-OLED board created for G6JME This is based on a design by Yogatech - Thingiverse thing https://www.thingiverse.com/thing:3443245 Designed to not require screws and so so no screw posts or bosses within the case. Antenna socket...

This is a case for a dev board with ESP32, a LoRa chip and an OLED made by Heltec, the board might not work the most well built, but it's handy for experimenting. The board often comes with a small coil antenna with a IPEX connector so I made space...

To hide the ESP32 for my WLED project I designed this case that fits for ESP32 Mini versions.I used an DC-Plug 5.6/2.1mm that comes from my Power supply, an XT30 plug to connect the stripe to the power, so that everything can be unplugged at any...

Case Upgrade for the ESP32 TTGO OLED Lora Module. This custom enclosure maximizes the module's compact design, albeit compromising slightly on ideal antenna positioning. ...In a brief trial run, I managed to achieve a transmission distance of over 5...

... To use the DHT22 you can steal it direct from the Chip. Pin33 (the red / blue LED) Edit: Cover for external antenna added: For an external antenna you need to change this: https://randomnerdtutorials.com/esp32-cam-connect-external-antenna/

Here's a case I made for this ESP32 based development board made by HelloBug. The product I have can be seen here:...

Ideal for ESPresense or any ESP32 application that doesn't require additional connected sensors.Designed around the following parts:FONKEN Power Adapter (https://www.amazon.com/gp/product/B07DCR29GN)D1 Mini ESP32...

... at https://www.amazon.de/dp/B07S83X9NM/ref=pe_3044161_189395811_TE_SCE_dp_1. For a tutorial on setting up the ESP32 Camera Web Server, check out this link: https://randomnerdtutorials.com/esp32-cam-video-streaming-face-recognition-arduino-ide/.

Simple case for an D1 Mini esp32 version. D1 Mini snaps into position with enough space below and above for soldering, and you'll also have access to the reset button. You'll find one version with a hole in the back and a lightbulb on the...

The top part is meant to be secured in place via glue.\r\n\r\nMy local glider club is looking to integrate these into many of their models, so I aimed for a minimalist design with a simple casing. ... If you're interested in building one yourself, head...

I crafted this case specifically for a friend of mine, and since he's already got one designed for him, I'm now on the hunt for a project to utilize it. Once I find something, this baby will be put to work! Given that, I figured I'd share it with...

This is a case for a dev board with ESP32, a LoRa chip and an OLED made by Heltec, the board might not work the most well built, but it's handy for experimenting. ...The board often comes with a small coil antenna with a IPEX connector so I made space...

An ESP32-WROOM-32/AZDelivery case where only the USB port is accessible. (For a Bluetooth-only application without the need for buttons or peripherals.) Modifications: - Closed pin holes on the bottom - Removed buttons, and the smaller-sized case -...

It is for the AI Thinker ESP32 CAM module, WITH the USB - serial card attached. It has a ball and socket foot, holes for the BRIGHT LED and camera, as well as the on board MicroSD card. The Micro USB has a hole in roughly the right place. The...

While working on a home automation project to incorporate temperature reading from every room in the house into Home Assistant (using a few ESP32 devices flashed with MicroPython, running some custom code I wrote to poll Mijia LYWSD03MMC sensors and...

MELIFE ESP32 D1 Mini Sled (case) - Board slides/snaps into bottom. Top then slides on a rail to encase the board. - Extra wide USB port - Topside extract for antenna area. - Mounting holes - no supports Note that this sled will only work...

I designed it to fit the Wemos Lolin ESP32 OLED https://www.ebay.com/itm/362946345220Printer: Ender 3 ProFilament: Hatchbox PLA Orange and BlackHotend: 215CBed: 60CDesigned in TinkercadSliced it in Cura 4.5Print SettingsPrinter...

This is case is used to take an ESP32 DevKit-V1 which can run off battery power - i.e. no wires. So - I wanted a cheap and easy way to battery power my ESP32. But - A normal AA battery is rated to about 50mA, and only runs maximally at 1.5v. So even...