esp01 case dht11 3d models

Category: 3D Printer Accessories

housing for DHT11

DHT11 Temperature Sensor

SENSOR DE TEMPERATURA Y HUMEDAD RELATIVA DHT11 / DHT11 RELATIVE HUMIDITY AND TEMPERATURE SENSOR

Simple DHT11 housing with 3mm cablehole. ...Lid snaps in place, no glue needed.

The ESP8266-01 module is paired with the DHT11 temperature and humidity sensor.

Simple DHT11 housing with 3mm cablehole. ...Lid snaps in place, no glue needed.

Just a mock for DHT11 temperature and humidity sensor module in real size.

This is the casing for the Wemos D1 Mini DHT11 shield, providing a labelled module that stacks neatly and offers a pre-fabricated shell for your IoT circuit designs. To assemble this build, you'll need these components: SOCKET JIG for soldering, 2...

Simple DHT11/22 holder (stand). Print instructionsDefault settings will do.

I need a DHT11 and a DHT22 to make a box, so I put them together in a .scad module.

This is a frame for the Schneider Asfora switch with a cavity for a DHT11 temp/humidity sensor. ...Print it with the flat side facing upwards.

A simple screw-to-the-wall type mount for a DHT11 temperature/humidity sensor. ...Compatible with screws with a 1/4" head.

... damit der umlaufende Snap-In gedruckt wird. ...(Im Slicer überprüfen, oder Kleber verwenden... :-) ) (DeepL)Simple housing for DHT11.I printed it with 0.15mm so that the all-round snap-in is printed. (Check in the slicer, or use glue... ...:-) )

The DHT11 Shield for Arduino is an effective tool used to measure both temperature and humidity in your environment. ...This sensor allows you to easily integrate these functions into your Arduino project, providing accurate readings with minimal setup...

I crafted a compact enclosure that cradles an ESP8266 module from WEMOS and a DHT11 sensor snugly. ...The device can still be rebooted with a simple paperclip trick, and it's designed to plug in effortlessly.

A small enclosure to stand in the room to hold a 16x2 LCD a DHT11 and WEMOS D1 Mini in it. The right for size for a IOT infoscreen. ... Category: DIY

The design includes a dedicated area where an M3 bolt and nut can be easily installed to firmly hold the dht11 temperature sensor steady. ... A modified version has been added, featuring a protective roof that shields the temperature sensor from direct...

I designed a compact case for an ESP01 module and an OLED-display. The case has a slot for a 2.54mm pitch screw terminal to power the board, while the backplate is held in place by pressure. An M2 bolt and nut secure the display. I built this project...

... basically never get hot (maybe bit while changing). Anyway, the grill adds some cooling just in case, looks nice and you can see the led of the sensor through it, giving you confirmation of proper charging and proper functioning of your esp8266.

DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...

DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...

Here is a simple housing for the DHT11 temp and humidity sensor that is mountable using two #6 screws. Ideal for indoor applications or outdoor locations that are undercover as this is not a waterproof housing. ... Check out the assembly video here: ...

A compact housing is needed to accommodate a 16x2 LCD display, a DHT11 sensor, and a WEMOS D1 Mini microcontroller within the same room. ...This enclosure must be specifically designed to fit all these components, making it ideal for use as an IoT...

This small enclosure was specifically crafted to safeguard the DHT11 sensor from mist or moisture that may settle on it, particularly in reptile habitats or areas where condensation accumulates. To ensure optimal airflow, the design features an open...

Lid snaps in place, no glue needed. Print instructionsCategory: Electronics Summary Simple DHT11 housing with 3mm cablehole. ...Lid snaps in place, no glue needed.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p...

Here's a simple enclosure designed specifically for the DHT11 temperature and humidity sensor. Equipped with two #6 screws, this housing allows for easy mounting in any setting. Perfect for indoor use or outdoor areas that are shielded from direct...

I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own.The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to anything conductive. ...There are...

Watch these informative videos to learn more about ASSIMILATE SENSORS: https://www.youtube.com/watch?v=5pK1bG-ngF0 https://www.youtube.com/watch?v=b2SkA1QkfuE https://youtu.be/mFCnvdzi1nk Discover the latest ASSIMILATE SENSORS on Thingiverse:...

DHT11 Sensor Housing for Reptile Environments. This simple design can be easily customized by any newcomer to the world of 3D printing. The backing is flattened, allowing for potential attachment using glue or in the future a custom mounting clip...