eryone 3d models

The level sensor is almost at the identical position, so it saves adapting the firmware.Ich habe nirgends ein Hotend halterung für eine E3D V6 ohne Firmwaremodifizierung für den Eryone gefunden. Meine Hotendhalterung kann an den originalen...

... nut for the screw attached to gantry. Please post makes, it's nice to see the makes. Print Settings Printer: Eryone Thinker S Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Mech Solutions PETG Black Category: 3D Printer Parts

This is the wire feed chain for the Eryone Thinker SE / S. I created the two initial and final supports and version 3 modules of [johnniewhiskey](https://www.thingiverse.com/johnniewhiskey). Questa è la catena passafili per la Eryone Thinker...

This is a remix of the filament holder for the printer Eryone Thinker Series. You can take over the original parts from your printer. I remix this as I want to use some 625ZZ bearings (5x16x5mm) I had and want have the grip on both sides with some...

I re-uploaded the original file courtesy of Eryone, accompanied by the remixed file that has resulted in a slightly increased height. ...Meanwhile, I noticed that in my own instance, the Y belt migrated upward due to friction, which ultimately prevented...

X-axis tensioner for the Eryone Thinker. Remixed from Janubis design. To assemble this component, you will need: * Two M3 nuts * One M3 x 25 screw * One idler pulley (You may reuse the original bearings, but they might be too tight) * Two M4 x 25...

This is an essential accessory for the Eryone Thinker 3D printer. Simply swap out the existing components with the new ones, and you're good to go. ...The versatile holder accommodates a wide range of filament roll diameters, ensuring seamless...

The Eryone Thinker S V2 spool holder features precision-designed bearings that perfectly fit the 54-73mm spool hole range. ...The bearings boast a sturdy 19mm outer diameter, a snug 10mm inner diameter, and a compact 5mm height, ensuring seamless...

Eryone ER-20 stop blocks left and right side while Gantry homing the Feeder crashes into Z axis spindel mount left side and z-Axis is not in level anymore the stop block can be adjusted for the right high on each side to stop the movement to the top...

This is a remix of the filament holder for the printer Eryone Thinker Series. You can take over the original parts from your printer. I remix this as I want to use some 625ZZ bearings (5x16x5mm) I had and want have the grip on both sides with some...

I made a new hotend mounting for the eryone ThinkerSE to accomodate the usage of 4020 fans. I have fittted noctuas on the printer. part cooling fan would benefit from a resin printed duct, as the rough surface inside results in less performance. ... ...

The heat-set inserts make the coupling of the hotend more rigid and durable. Come to Eryone 3D Italia Facebook Group for support and more mods! Print Settings Printer: Eryone Thinker SE Rafts: No Supports: Yes Resolution: 0.28 Infill: 50%+...

Didn't like the existing "fixes" for the bed cable snagging on the 2020 extrusion on the Eryone Thinker printers so I made this. Fits both the Thinker S and SE with enough clearance for the bed gantry and insulation. ...Print Settings Rafts: No...

This adjustable bracket allows Eryone ER20 to use the 3D/BLTouch standard sensor. As requested by an individual, who has other mods on the ER20 hot end housing. ...A remix from my All-in-One adjustable design:https://www.thingiverse.com/thing:4914705

This is simply an enhanced cable management solution designed to complement the official Eryone bl-touch mount. ...Concerned about the fragile bltouch sensor cables that continually rubbed against the sharp edges of the bl-touch mount, I've created two...

Mount for changing Eryone Thinker SE bowden extruder to a direct drive. I found other models but they did not fit on my Thinker SE. There must exist multiple versions of the Thinker SE. ...In my case, the extruder mount is metal not plastic (I think...

Real simple redesign to extend this for the Eryone Thinker to clear the circuit board on the extruder side of the gantry, also add a top ring to make it easier to align. Hardware required was 12 M3x16mm (12mm may work) screws and some washers\lock...

The Eryone Snail Dry Box has a small compartment underneath for desiccant bags. Unfortunately the grid spacing that allows airflow is too wide to put your own desiccant. This simple box allows you to put your own desiccant without all of it...

Mount for changing Eryone Thinker SE bowden extruder to a direct drive. I found other models but they did not fit on my Thinker SE. There must exist multiple versions of the Thinker SE. In my case, the extruder mount is metal not plastic (I think...

Eryone Thinker PS Rear Mount Mod: BOM: 4 X (M4 10, M4 T-slot, M4 Washer), you might have to use two washers if it's not tight enough. ... When it's done properly, it should have about 10mm to the moving build bed, and 30mm to the right stepping motor.

Real simple redesign to extend this for the Eryone Thinker to clear the circuit board on the extruder side of the gantry, also add a top ring to make it easier to align. Hardware required was 12 M3x16mm (12mm may work) screws and some washers\lock...

This is an alternative cover for the original Eryone thinker SE power supply Required Items: Power Switch Fused IEC 320 C14 like this : https://a.aliexpress.com/_vqAMO5 Power Meter (this is for AC) like this: https://a.aliexpress.com/_uX3zgN

Eryone started using cardboard spools. This is a fast print, if you use these settings, it is about 12 minutes on the X1C.The little lip hold the spool, and the single tab keep the ring on the spool while keeping as many holes open as possible for...

Eryone Y-axis belt idler belt bracket. A friendly tip: Print at least one copy before you regret you didn't do it, undeliverable, it's one of the lives and dead spare parts. Printing: Print it on its back, no support is required, 0.2...

...Print Settings Printer: Eryone Thinker SE Rafts: No Supports: Yes Resolution: 0.3 (support) - 0.16 (bltouch) Infill: 40-50% (support) - 20% (bltouch) Filament: Eryone PLA Grey Notes: 1.2mm walls 0.9mm top/bottom Supports needed for the support only.

Files: - ThinkerS -DirectDrive [No Logo] - ThinkerS -DirectDriveL [with Eryone Logo] - ThinkerS-DD-BL.stl [BL Touch Mount] Enjoy! ... YT: https://www.youtube.com/watch?v=TXLjdwfAkwY&feature=youtu.be ##March 26 2020 Added Bltouch mount...

... old cable from right side of printer might work but I havent tried it. Files: ThinkerS -DirectDrive [No Logo] ThinkerS -DirectDriveL [with Eryone Logo] ThinkerS-DD-BL.stl [BL Touch Mount]   Enjoy! ... YT: https://www.youtube.com/watch?v=TXLjdwfAkwY

... inserts are required for the hotend screw. The heat-set inserts make the coupling of the hotend more rigid and durable. #### Come to [Eryone 3D Italia Facebook Group](https://www.facebook.com/groups/435804983883632) for support and more mods!

(DE/EN) Staubabdeckung für den Filamentvorschub zum Extruder des Eryone Thinker S/SE, könnte auch beim Creality CR-10 (Max) passen weil die beiden wie Zwillinge aussehen (jedoch ohne Pass-Garantie von meiner Seite). Die Staubabdeckung und...

... I remade one with openSCAD that was adapted to the screws I got and accepted the tapping die. ... The openSCAD can be found [here](https://github.com/MerryKombo/3DDesign/blob/psu/assets/printers/Eryone/Thinker%20SE/BL-Touch-adapter.scad).