eryone 3d models

Eryone Y-axis belt idler belt bracket. A friendly tip: Print at least one copy before you regret you didn't do it, undeliverable, it's one of the lives and dead spare parts. Printing: Print it on its back, no support is required, 0.2 resolution,...

The biggest upgrade made to my 3d printer was to switch from stock hotend+extruder combo to a direct drive v6 setup, using the Eryone Thinker SE Direct Drive mod BMG + E3Dv6 (Including Volcano) project.I was overall satisfied, if it wasn't for a...

BOM: 2x M2x8mm screws 1x M3x6mm screw 5x M3x10mm screws 4x M3x16mm screws 1x M3x20mm screw 1x M3x25mm screw 2x M3 nuts Any question not specific to the Eryone Thinker has probably been answered in the source:...

I recently got a 3D pen and needed a holder for it, so I made one myself. Here's the result. I'd love to see your creation! ...Thanks in advance.

<p><strong>(Description in german below // Deutschsprachige Beschreibung folgt unten)</strong></p><p>I recently received a 3D pen for which I needed a holder, so I made one. Here it is.</p><p><strong>Please post your make. Thank you. Hier ist...

I adapted the original design for installation on an Eryone Thinker SE printer. The main changes to the original design are: - Top Bracket: Reduced in length to improve rigidity. (No reduction on maximum print height) - Top and bottom ends: Use...

Este es un mod para poder montar un V6+Bmg en directa con guias lineales en una Eryone Thinker SE. Esta pensado para poner doble ventilador de capa tipo turbina de 4020 24V y ventilador de hotend 3010 24V. Todas las piezas estan hechas con PETG...

Eryone ER-20 Sunlu Dryer Mount Remixed from d3arts Holder Move bracket toward front flush to the frame, draw a centre line in line with the centre of the v-groove, cut down and re-drilled new holes on the original bracket where you marked it, re...

Eryone ER-20 Sunlu Dryer Mount Remixed from d3arts Holder Move bracket toward front flush to the frame, draw a centre line in line with the centre of the v-groove, cut down and re-drilled new holes on the original bracket where you marked it, re...

It happend, when i used this spool holder that you see in the pictures, that the eryone spool was wandering left and right and also started to tilt a little. So i created this insert as a guide for spools with carvings at the side. (i am sorry to...

Reusable centers for Eryone .5 and 1kg plastic spool. Uses plastic water pipe or conduit (about 25mm outside) as the shaft because I had a bunch lying around. (loose fit) Using...

Made specifically for Eryone Thinker+S+SE model printers. Designed to work seamlessly with the stock hotend setup. A revised version will be made available to accommodate custom hotends. 1) Frame Brace 2) Lead Screw Mod 3) Mounting solution (for...

https://www.thingiverse.com/thing:4914705 Note: For those individuals who prefer not to have 3D/BLTouch, please download the z-end stop plate for this mod from the Eryone Forum site: https://www.eryone.com/forum/download/file.php?id=466 H. Mount the...

https://www.thingiverse.com/thing:4914705 Note: For those individuals who prefer not to have 3D/BLTouch, please download the z-end stop plate for this mod from the Eryone Forum site: https://www.eryone.com/forum/download/file.php?id=466 H. Mount the...

This is for ALL Eryone 3D printers (Thinker S, Thinker SE and ER-20) as they all use the same stock hotend. 2. You do not need to print the part for cutting the tube unless you'd like to. You can use callipers to cut a piece of PTFE tubing to...

Made specifically for the Eryone Thinker+S+SE model printers. This is made to work with the stock hotend setup. I will be making another version to work with the extra bulk of custom hotends 1) Frame Brace 2) Lead Screw Mod 3) Mounting solution (for...

Make sure to connect the signal wire correctly, it's the one with the white cylinder on the 3d printer side, and needs to go to the right side of the sensor (yellow wire in the pictures)Install the correct marlin firmware on your 3d printer...

Original design is good but was touching the heat block/sock on my stock thinker se and melted on a few spots. This has a wider opening so does not touch the heat block. ... Remixed from: https://www.thingiverse.com/thing:4119897/comments

I Remixed this as I want to be able to use M3 nuts to fasten the Head to the adaptor and want to allow for some horizontal adjustment for the head...incase the X offset is slightly off. I also made the Y Axis offset adaptor to be adjustable in...

I like this PSU Fan Shroud and remixed this as I want the logo to be inset instead of raised and to have the logo and font have the correct aspect ratio. I made variations of it with both raised and inset and with out the text, in hide site I would...

Today's breakthrough is a game-changer. The rulers on the side are a great idea, but they're hampered by their positioning - the end stop covers them on the left, while the triangular bracket gets in the way on the right. You can't rely on a flat...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

17/04/2020_WORK IN PROGRESS -Add upgrade part for: 1/ X axis with MGN12 and Support for Titan Aero with Optical End stop.(TESTED) 2/ Support for M8 screw on Z axis and Bearing guide for Leadscrew on top.(NOT TESTED)

This spool holder fits over the existing one increasing its diameter and even use large filament spools like from the Sunlu brand. This way the spool can roll easily, putting less strain on the printer and reducing vibrations during retractions.

Improved ER-20 filament guide to reduce the pull on the tube. Can be printed without supports lying on the side. It clips easily onto and holds the bowden tube instead of the filament. ...

I remixed this spool holder as I needed it to be wider to accommodate some spools slimmed down for other spools that had a narrow centre. Also added a 3rd bearing spot. Lastly I added a small hole near the bolt to insert and hold the filament when it...