eryone filament 3d models
210497 3d models found related to eryone filament.
prusaprinters
Make sure to connect the signal wire correctly, it's the one with the white cylinder on the 3d printer side, and needs to go to the right side of the sensor (yellow wire in the pictures)Install the correct marlin firmware on your 3d printer...
thingiverse
Reusable centers for Eryone .5 and 1kg plastic spool. Uses plastic water pipe or conduit (about 25mm outside) as the shaft because I had a bunch lying around. (loose fit) Using...
thingiverse
This is a (quite over engineered) filament runout sensor mount to be used together with a bltouch (as it frees the z axis sensor). It fits my particular setup, so check the list below to make sure it works for you! To be able to use my mount you...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
This is a hub for the filament spooler holder of the Eryone ER-20 that includes two ball bearings 10x30x9mm. The 10mm ID of the bearings fit perfectly on the spooler holder. The Cura based gcode will stop at the right height in order to insert the...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Suitable for Eryone filaments. ...Users' feedback paper spools are not suitable for the AMS. And sustainability has always been Eryone philosophy. Print these Spool Rings, then you can make Eryone filaments work on AMS.
thingiverse
I Built a Spool Holder For My Cr-10 To Hold Eryone Filament
prusaprinters
Made a spool holder for cr-10 for eryone filament Category: 3D Printing
thingiverse
Design a custom spool holder to perfectly fit your Eryone filament spools within the Monoprice Maker Ultimate 2's internal dimensions, ensuring smooth and hassle-free printing operations. ...This adaptable solution can also be repurposed for various...
thingiverse
Quick solution to prevent the Eryone Filament spools from slipping off-center on the Anycubic Mega-S spool holder, ensuring they align perfectly with the sensor at all times.
thingiverse
Customized version of https://www.thingiverse.com/thing:5486758 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5486758
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
cults3d
Tensioner for Eryone thinker SE Very easy to print and install We keep the 2 screws of the original tensioner Provide 4mm x 40mm threaded rod or screw cut A small bearing of 3mm x 10mm A 3mm pin or cut screw for the bearing 3 nuts of 4mm. ...2 for the...
prusaprinters
... Thinker to match the leveling knobs on the bed. ...Please post makes, it's nice to see the makes. Print Settings Printer: Eryone Thinker S Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Giantarm PLA Black Category: 3D Printer Accessories
prusaprinters
... Eryone Thinker Bed Leveling Knob style. ...Please post makes, it's nice to see the makes. Print Settings Printer: Eryone Thinker S Rafts: No Supports: No Resolution: 0.2 Infill: 25 Filament: Mech Solutions PETG Black Category: 3D Printer Accessories
prusaprinters
... Eryone Thinker Bed Leveling Knob style. ...Please post makes, it's nice to see the makes. Print Settings Printer: Eryone Thinker S Rafts: No Supports: No Resolution: 0.2 Infill: 25 Filament: Mech Solutions PETG Black Category: 3D Printer Accessories
prusaprinters
Really quick simple design for mounting the ADXL345 Accelerometer to my Eryone Thinker Series printer for tuning with Klipper. Require 2 x M3 6mm, 2 x M3 8mm (for bed mount) & 2 x M3 16mm or equivalent for head mount. Print Settings Printer:...
thingiverse
Resolution: 0.2mm Fill: 30% Adhesion: Brim (10 counts) Support: No Filament: PLA Color: Any BOM: M5 x 15mm (or reuse the original one M5 x 10mm) M5 nut Optional lock washer Drop in the M5 nut from the top of the slot, (the hole is already threaded,...