eq2 mount 3d models
387037 3d models found related to eq2 mount.
thingiverse
Simple lens shelf for Sky Watcher EQ2 mount. Couldn't find any, so I've designed one. ... Enjoy!
thingiverse
... The bracket and spacer are designed as replacements for the original part of the SkyWatcher 130M EQ2 Equatorial Mount. ...As a matter of fact, my first attempt at designing these parts from scratch was a real challenge, but it paid off in the end.
cults3d
the piece that is used to fix the nut didn't work well for me and I made a cut in a piece of metal to replace it the bolt inside is stuck in the metal piece so it doesn't turn on itself when tightening the screw.
thingiverse
NEW VERSION MUCH MORE RIGID (2020/04/09) I offer a female aronde queue of type vixen to install on EQ2 equatorial mount. It can accommodate male aronde queues up to 110 mm maximum. The principle is simple. The aronde queue is in two parts and an M6...
thingiverse
NOUVELLE VERSION PLUS RIGIDE (2019/06/20) Je propose une queue d'aronde femelle de type vixen à installer sur monture équatoriale EQ2. Le principe est simple : la queue d'aronde est en deux parties et un boulon M6 les resserre l'une sur l'autre pour...
cults3d
Leveller , for equatorial mount Eq2 For 49.6 mm retainer connector for mini circular level diameter 18 mm
thingiverse
I built a component to fix the busted bracket of my EQ2 mount's base.
thingiverse
Bricolage modification and motorization of an eq2 equatorial mount. -Dismantle the entire assembly, remove or modify parts as needed, make sure to lubricate axes for smooth operation but avoid over-lubrication. -Print parts with 30% infill at...
thingiverse
3 pieces to mount a telescope on a EQ2 mount. Normally that mount has you bolt the rings to the mount, and then open the rings to remove the scope for transport. But that pretty much locks you into using that one scope on that mount. This device...
thingiverse
... I'm thrilled with its performance so far. ...I've been using it on my Newton 114/900 and it's made a huge difference compared to the EQ1 and EQ2 mounts. ...To enhance stability, I've added Teflon pads from Stabilit and some gliders from Ikea.
thingiverse
plateau pour trépied fournis avec monture eq2
thingiverse
Salut pour ceux qui on une eg2.3 et qui comme moi l'on cassé a niveau des réglage des pieds je viens de dessiner et imprimer un piece de remplacement
thingiverse
The original base of the three-legged support was not spread far enough apart. This one spreads the feet further apart for greater stability of the tripod. It also allows you to place your 31.75mm (1 1/4") eyepieces on it. Since there is hardly any...
thingiverse
Pièce de remplacement de la charnière sur un trépied de télescope EQ2, pour le coup un 130/900 de chez Omegon mais je pense pas me tromper en disant que ça passerait certainement sur SkyWatcher de même taille. Remplacement de la visserie d'origine...
thingiverse
I got a Skywatcher 90/910 and I would like to watch the Mars and other planets. You need a clock drive for RA axis that will compensate for the Earth spinning. I created and made a solution for me (and for you). Parts: - 3D printed parts...
thingiverse
Filament : PLA, PETG ou ABS Supports : NON A prévoir : 1 vis 6mm, assez longue. ... -------------------------------- Filament: PLA, PETG or ABS Supports: NO To provide: 1 screw 6mm, long enough.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=536645 Instructions Using the following options: mount_tube_dia: Eleven mm mount_wall: Three mm nut: Five point five mm servo_flange_width: Thirty-five mm mount_angle: Eighty degrees screw:...
grabcad
The given mount serves the purpose of securing and positioning a butterfly valve properly, ensuring its functionality.