eppendorf microcentrifuge tube vortex adapter 3d models

I needed to vortex 20+ Eppi tubes at once for some biology experiments. This thing lets me do that! ... Only other part required is a small length of ~8mm rod (could probably get away with printing it).

The outer diameter of 1.5mL Eppendorf microcentrifuge tubes is approximately 10.9mm by my measurements. However, when printing with a 0.8mm nozzle, I had to design the holes as large as 12.2mm for the eppendorf tubes to fit easily. I have not...

It has been designed to store solution at 4°C in microfuge tubes if you manage to print or build it in aluminium for example. The carrier respects the standard dimensions and should fit all pipetting robots (Beckman, Tecan, Hamilton). This carrier...

Link to publication:http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...

Link to publication: http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...

Equivalent to what is sold as an "Eppendorf tube adapter" for cytometry. ...The printed part must be glued to a cytometry tube cut 32 mm (1 1/4'') from the top.

A microcentrifuge tube, also referred to as a PCR tube, is a small, thin-walled, and conical test tube used primarily for holding samples during the centrifugation process. ...These tubes are commonly found in laboratories and are designed to fit into...

By using this adapter you can put an eppendorf tube in a falcon 15 mL, you will say, what is the use? ...I use that with Frac-920 of AKTA purifier to have the liquid droplet in the middle of the tube and not just close to the edge of the tube (when i...

I designed stand for one 1.5 mL Eppendorf tube and one for a 15 mL centrifuge / falcon tubes to be placed on a scale to weigh in a sample and want to share them with you.

Used in combination with the bottom part of the Craft paint adapter, by Kristof65 https://www.thingiverse.com/thing:3155194

This adapter plate conforms to the universal 33x2mL tube plate specification. Its hole arrangement has been verified, and it accommodates tubes featuring or devoid of a skirt plus labels; however, cleaning with a drill might be necessary based on...

... ...For use with 1.5mL Eppendorf tubes. Similar to those found online. Significantly cheaper to make them with a 3D printer instead of buying them. Print with no supports if doing the one with built in ones. ...Should print out just fine at 20-40 %infil

A 90mm by 90mm sized microcentrifuge tube comes in the shape of a square, ideal for various laboratory applications.

Larger than normal size microtube rack for all of your biology needs! ...Fits most standard sized microcentrifuge tubes with plenty of room in between tubes.

This is a small rack for 1.5 ml microcentrifuge tubes (11 mm diameter). 20 tubes can be stored in the rack. ... The rack consists of four different parts which have to be put together and can be secured with two M3 nuts and two M3x16 screws if...

This is a simple rack to hold four 1.5 or 2.0 ml microcentrifuge tubes. Tubes from different manufacturers should be more or less the same size, and the few brands I've tried have fit fine. ... ...

Perfect tube tack for smaller projects!

A sleeve to fit 0.6 mL tubes in 1.5 mL size centrifuge holes

This is a StageTip Adaptor for microcentrifuge tube for stagetip made with peptide tips. It provides more secure holding of the StageTip in the eppi tube so it can be span at a higher speed to shorten washing and elution step. ... Gcode included to be...

I designed this box to put my Eppendorf tubes in during incubation, this allows me to lie the tube on its side in the shaker without the worry of the tube popping open. Can print without supports if oriented in the correct way. ... I currently...

An Eppendorf tube rack for smaller projects. ...Holds 12 tubes.

A 5x5 mini eppendorf rack that holds standard 1.5 ml eppendorf tubes.

A closed-lid container specifically designed as an Eppendorf tube

Vortex tube

Vortex tube

... on the balance easier. Edit 9/26/2018: Updated V3 for 5 mL tubes, removed V1 Updated V2 with a slight incline on the bottom of the holder. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/7rSmxc9lKFF

I designed stand for 4 oder 8 times 1.5 mL Eppendorf tubes and want to share them with you. ... Others can be designed and uploaded on request.

support pour tube eppendorf. ...Sur la droite, il y a de la place pour mettre une feuille afin de savoir ce qu'il y a dans les tubes.

Also, you can choose the distance between the Eppendorf tubes to make them stand tight or rarer. It is possible to add a skirt for stability and change the height of the rack. ... You could generate any sizes grid, or you can download one of the...

Also, you can choose the distance between the Eppendorf tubes to make them stand tight or rarer. It is possible to add a skirt for stability and change the height of the rack. ... You could generate any sizes grid, or you can download one of the sample...