ender3 v2 3d models

... mini Ender3 Pros, and I was jealous because my Ender3 V2 doesn't have a "mini me", and I love my printer with all my heart. ... So I measured and modeled my Ender3 V2, scaled it down 1:10, and made all 3 axes able to move like how the big printer does.

Ender 3 v2 hotend mount for Wanhao i3

- No support needed - I printed it at 0.1mm layer height, but any reasonable layer height should do - 10% to 15% gyroid infill ##REQUIRES: - 4x screws m2.5x8mm (those were included with my dragon hotend) - 3x screws m3x8mm for mounting it to the...

this is a mounting plate for the ender 3 v2 BLtouch best printed from ASA or ABS with 25% infill and 3 perimeters

My first try with fusion 360, i liked this drawer but wanted the creality logo on it Print Settings Printer: Ender 3 V2 Rafts: No Supports: No Category: 3D Printer Accessories

This solves 2 issues with the original part: 1 - One of the 3 fixation points to the gantry was moved to match Ender 3 V2 (this gantry is slightly different from the Ender 3 and Ender 3 Pro) 2 - Added 3mm spacing to give clearance between the hotend...

If have gone and wished you had a better and more straight Bed on your Ender3, Where flatness does not vary from time to time when heated, then there is no need to wait. Buy a 5mm "non-rolled" bed that is stable. Depending on which heating mat you...

Basically i added place for the sdcard reader, simple and hacky but works pretty wellFor details how to print check the originalFor Ender 2 V2 Neo users you can either use the 3mf file in prusa slicer where i've already added supports, or use the...

This is a remix of the V1 and V2 BLTouch models from https://www.thingiverse.com/thing:4647053 (I take no credit for the original models). STEP file is available for V2, I don't have a STEP for the V1, just the modified STL. Necessary hardware: ...

I wanted to mount my ender 3 v2 screen on the out side of my lack enclosure. Really like the horizontal screen but did not want to lose the drawer or have screen inside. I just copied the mount from the right and added it over to the left. ...With a...

This is a remix from tllado's Quiet Cooler for Creality Ender 3 v2 (https://www.thingiverse.com/thing:4969159) This is just a modification of the right fan shroud to mount a button holder for a camera to enable you to do time lapses. This is...

This is a remix from tllado's Quiet Cooler for Creality Ender 3 v2 (https://www.thingiverse.com/thing:4969159) This is just a modification of the right fan shroud to mount a button holder for a camera to enable you to do time lapses. This is designed...

... a 1/4 20 bolt and nut to mount the Harbor Freight dial gauge. Printed using ender 3 v2 This printer was not listed as a choice on drop down box for printers used. I think it took around 4 hrs. ...to print (but honestly I do not remember for sure).

The MinionD Ender 3 Dual Duct was a remix of that design which made some nice improvements to the original design like thicker duct walls and a press fit design. My remix builds off of both of those designs to enlarge the air inlets slightly as...

https://www.thingiverse.com/thing:4819097 My remix builds off of VortexPC's design to enlarge the air inlets slightly as well as modifying the press fit region to fit an Ender 3 V2 cooling fan. I'm not sure if the stock fan on the V2 is the same as...

https://www.thingiverse.com/thing:4819097 My remix builds off of VortexPC's design to enlarge the air inlets slightly as well as modifying the press fit region to fit an Ender 3 V2 cooling fan. I'm not sure if the stock fan on the V2 is the same as...

Remixed drawer for Ender 3 V2. I use it for Raspberry 3A+ and Waveshare 4,3inch touch screen. Screen can be moved to be accessible also during the print when bed is in front (see pictures which shows edge positions. Changes: 1) Raspberry pi mount...

... get the tiny pieces out from inside the pegs.. make sure you have some tweezers and small pliers. Update 21/01/15: Endcapholder_v2.stl will provide better access to the drawer (shifted it 2mm) and added slightly more support to improve sturdiness.

It is a mounting part for CR-Touch used in combination with Briss fang v4.3. ... https://cults3d.com/en/3d-model/tool/ender3-v2-dual-40mm-fan-hot-end-duct-fang

It is a mounting part for CR-Touch used in combination with Briss fang v4.3. ... https://cults3d.com/en/3d-model/tool/ender3-v2-dual-40mm-fan-hot-end-duct-fang

Ender3 V2 damper raiser feet with with circles for rubber/silicon pads. Raises the printer for ~16mm. ... Print in 70 - 100% infill, or even better with a lot of parameters.

3 Point Print Bed Leveling for Ender3 v2. It needs to practice a hole with the drill exactly halfway through the distance of the 2 side holes. The bed will continue to work because the heating path is missing where the hole is done. ... 2 screws +...

Support for an adapter for Micro SD to MicroSD extension for ender3 V2 I made it a little bigger so the flat cable won't have any stress because it's bending Print info: Material: PLA Nozzle diameter - 0.4mm Layer height - 0.2mm Print info:...

I couldn't find anything to fit the Ender3 V2 to hold a Dial Indicator I had - hence this project. The BL Touch hasn't worked for me at all, but this design attaches to the folded metal bracket provided by that product. Design file for editing in...

I needed a bracket to mount my 3D-Touch on my new Ender3 V2, and after looking around, decided to make my own. This one is super simple, the holes line up, there is enough clearance, and it seems stable enough. The M3 lock nuts should just...

This is a First Layer print for people who are using Jyers UI for the Ender3 V2, for manual mesh leveling in a 5x5 grid. This takes into consideration the clips that are at the front and the end of the bed as well. I know this takes a long time...

I wanted a different fan shroud for My Ender3 V2 with the MicroSwiss Direct Drive Extruder. The one they suggest on their website is quite large and bulky and was tough to print in ABS. I made the mistake of thinking I could use PLA to print the...

UPDATE: V2 with hole for hex key (24.03.2021) You need the lcd-cover.stl and spacer.stl from the original by otioss "please don't forget to set #define LCD_FLIP 1 in the firmware according the the guide." -otioss visit [otioss...

https://www.thingiverse.com/thing:3854400 Update V2: Handle arch widened to match Ender3 V2 belt adjuster box I needed a compact handle that wouldn't stick out too far from the bed, so I could fit my printer in a cabinet. The handle grabs onto it...

The official Dragonfly HIC cooling duct mounting for Creality Ender3 V2 Phaetus, a supplier of core parts for high - end 3D printing equipment Focus on the upstream market of 3D printing Supreme Pursuit ►Follow Phaetus to get the latest official...