ender3 v2 neo fan duct 3d models

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

# Mount To mount it, print 2 fan spacers of 4 mm, the adapter and the fan duct, you can also refer to this video : https://www.youtube.com/watch?v=rMP1BdaEl2M&list=LL&index=41&t=203s&ab_channel=Curiosity3D # Tip It may seem complicated but once you...

I've Upgraded My Short Fan Duct for the Anet A8 to Fit Better and Stronger in Its Holder. Check Out the Improved Design! ... http://www.thingiverse.com/thing:2151906 Print Settings: Printer: Anet A8 Rafts: No Raft Needed, I've Got This Covered Supports:...

The images are from the giantarm grey pla, just for testing it is fine, currently this pla fan duct continue on the printer, but if you want a heavly use, try to print it at least on PETG. **IMPORTAN NOTE:** Since the lower screw holes are in...

This fan duct is based on EvoCivic's Sovol SV04 version. worth printing at least from PETG or any more heat-resistant filament. i printed my test version from PLA, but later on I will definitely replace it with something more resistant. ... ...

Ender 3 v2 Modifications for the Hydra Includes: E3V2 variants of rear and side brackets (threaded insert variant) Modified Narrow default ducts with built in BLTouch 3.1 mount hugging the left side Flat Hydra tool plate head for when using cables...

**Alfawise u20 Precise Fan Duct** It's used for precise lithographic printing, making tracks of PCBs, and it's not recommended to use it to print conventional pieces. This is very important - you'll make this ventilation duct do its job very well...

I remixed the original design by __Plasma__ on Blender and duplicated the support structure he had on the screw tab to the left portion of the fan duct, stretching it a little bit to have its center of gravity on the part that is held by the screws.

This duct is virtually identical to the other fan duct with one very important exception. Airflow is now more focused on the nozzle due to a reduced opening near the hot end. It still prints well (even better) without supports and there are two...

Based very loosely (ie inspiration) on the Cr10 Pro fan duct by Plasma https://www.thingiverse.com/thing:4391624, which I had been using for some time however it didnt print well in abs. This was a ground up design from scratch in Fusion 360. ...

This is version 2 of my fan duct design for The FOKOOS Odin-5 f3. It is an upgrade to my original design and has several improvements based on comments from FOKOOS users. It is slimmer with better airflow, has more clearance at the bottom, and has...

... parts need support to print (2 parts of mounting), other parts don't need support. You can see the step file to know how to assemble it. You will need: 4x 30mm M3 4x 16mm M3 1x 10mm M3 1x 8mm M3 1x 4020 Blower Fan 24v (remove the stock 4010 fan)

You can choose between these versions: cover_v2_4010 (original stock fan usage 40x40x10mm) cover_v2_4020 (if you wanna use a 40x40x20mm fan) cover_v3_XXXX (v3 versions have vertical venting holes - if you have problems with printing large bridges)...

This duct is virtually identical to the other fan duct with one very important exception. Airflow is now more focused on the nozzle due to a reduced opening near the hot end. It still prints well (even better) without supports and there are two...

This is my second attempt at designing a dual fan duct for the mosquito hotend on the SecKit SK-Go. My main focus with this design is to fully utilize both the x and y axes, even when an enclosure is used. It can accommodate a 40mm fan and is also...

The focus of the design was to ensure as much cooling as possible while keeping the weight down (considering 2 x 5015 fans were used). Parts 4 x M3x15 Self tap 4 x M3x20 Self tap 2 x M4x20 Bolts and Nuts (Optional) 1 x Small Cable Tie To use a...

The focus of the design was to ensure as much cooling as possible while keeping the weight down (considering 2 x 5015 fans were used). Parts 4 x M3x15 Self tap 4 x M3x20 Self tap 2 x M4x20 Bolts and Nuts (Optional) 1 x Small Cable Tie To use a...

I made a channel inside the model to allow it to be printed flat on the build plate without needing support for the long duct, your printer will "Bridge" easier with this channel in place. I recommend ABS because PLA and possibly PETG will sag...

... top and corrected some minor issues. Print Settings: Printer: Anet A3 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100% Notes: 1st layer: print at slow or medium speed, no fan. ...2nd+ layer: print at medium or fast speed with normal cooling.

Secure the fan duct to the Extruder holder with leftover inbus screws and quadratic nuts (3mm x 20mm) from your Printer assembly. Geeetech consistently delivers an abundance of screws, making it easy to find exactly what you need. Leave a comment...

This new design combines the original Predator fan duct with an LED ring, all in one solid piece. The LED ring support is thicker than on the previous model. It's designed so that the LED ring glows nicely through transparency across the PLA. ... I've...

... be a bit lower and longer. Despite this, significant airflow persists on the far side of the nozzle even with its current design. Additionally, the end of the heat-break duct may require trimming, assuming your printer excels at handling overhangs.

Manufactured after high-performance heat dissipation channels on the elite Monoprice Select V2.

I designed this project specifically to work with my RF100 V2 3D printer, allowing me to fully utilize the build volume. ...This design is a creative reinterpretation of the original found at Thingiverse under reference number 2431530.

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

Designed for an inlet slot on Ramsey STE3000F to improve airflow to the enclosure. ...Fits 120mm fans that can be stacked on top of each other.

... than its predecessors, this model showcases improved efficiency and exceptional airflow management. ...Its performance is poised to meet or even surpass expectations for a wide range of 120mm fans, making it a reliable choice for various applications.

I would print this before you get that MicroSwiss all in one Direct Drive. ...this will keep the same fans and mounts with also the same space for the BLTouch.

used all the original fans and hardware. printed face up with tree supports. has about a .5 mm clearance to the part when printing. designed in fusion 360 uploaded both the stl and the F3D files Update 1/3/21: i moved the mount holes to move the...

This is an electronics fan cover for version 2 of Geeetech A10M printer. Older versions of the same machine had the electronics on the left and designed a bit different so most of A10M covers don't fit properly. You can't attach them to any existing...