ender3 max 3d models

Mainboard silencer for ender3 Max with the fan on the underside. I couldn't find any other person who had created something for this model so I decided to tack a whack at it. This is my first 3d model on my own without any kind of tutorial. I hope...

An adapter for the Ender 3 Max! ...Figured i would upload this to save you Ender Max guys some time :)

Direct extruder bracket for ENDER 3 MAX. Extruder motor wiring needs to be extended. ... It is offset 5 mm from the extruder to the hot end.

slicer cura normal profile took 8 hours print no need support

Bracket for moving the power supply used when the Z axis of the ENDER 3 MAX is modified to dual

... the design based on feedback. ...although they worked perfectly before. I added a second Z axis to Ender 3 Max. I couldn't find a jig that fit in the lower extrusions of the Max so I designed one. ... No Supports It's basic, but does the job.

I couldn't find a jig that fit in the lower extrusions of the Max so I designed one. No Supports needed It's basic, but does the job. I added a vs2 as some people had said the v1 didn't sit flush on their printer. Due to the control box. ... Video of...

This is a X gantry leveling jig for the Ender 3 Max. Sometimes my dual Z get's misaligned and then I need to readjust. Instead of crashing it into the top frame, I always opted for this jig.First make sure your Z axis is somewhat high up, so you can...

This is a X gantry leveling jig for the Ender 3 Max. Sometimes my dual Z get's misaligned and then I need to readjust. Instead of crashing it into the top frame, I always opted for this jig.</p><p>First make sure your Z axis is somewhat high up, so...

Remix of https://www.thingiverse.com/thing:4856613 added a GoPro mounting bracket using a file from https://www.thingiverse.com/thing:2584426 printed at a 0.28 layer height. use supports. You can use only supports on the print bed, as...

Ender 3 Max / Max NEO brackets to retro fit Creality's LED light Bar Kit onto a wider printer. I already had the light on hand and was happy with the hookup with the smaller printer so decided to adapt the same light bar over to my NEO. ... Brackets...

This fan duct is for those who want dual 5015 cooling for the Ender 3 Max, without having to do a bunch of other modifications. This fan shroud does not interfere with the standard CR Touch mount! Just slap two 5015's on and you're set. This is...

Remix of https://www.thingiverse.com/thing:4856613 added a GoPro mounting bracket using a file from https://www.thingiverse.com/thing:2584426 printed at a 0.28 layer height. use supports. ...You can use only supports on the print bed, as the go pro...

<p>To print use 3 walls, and 4 solid top and 4 solid bottom layers and 15-20% infill. Te part was printed with azure petg, and this part have a fox for creality sensor, the litle pin from the top keep the roll form the switch in good position. ...And is...

The pins in the model are negative modifiers that will slice into holes.  I didn't model this in CAD, it's just shapes cut together in Prusa.  Mount your filament sensor directly to the hotend for an accurate runout distance rather than a variable...

Original had the V-rail prongs at 22mm centres instead of the required 20MM, it still worked fine but did not sit fully flat on the profile. Also cut a wee bit off the width of them as it was a tight fit where the control box is sat over the...

This fan duct is for those who want dual 5015 cooling and a Revo CR hotend for the Ender 3 Max, without having to do a bunch of other modifications. This fan shroud does not interfere with the standard CR Touch mount! Just slap two 5015's and a...

Note: The Kobra Max and the Vyper use one fan header for both part cooling fans so you will need to splice the two 5015 together. The led on the Kobra can be cut and run through the hole directly under the heat sink fan, or hot glued or super glued...

Simple Knob lock for Creality ENDER3 max neo

My toy Max Max is a character of my illustrated book.

MAX man People room studio corner 3130_3130

"Block by Max": A creative and engaging piece of work, showcasing the artistic prowess of Max. ...This intriguing construction, titled "Max's Block," captures one's attention and invites further exploration into the depths of Max's imagination.

I did this so my Ender3 MAX Neo has a chain, and since no one has shared something similar i decided to share it, i used the work of wku_wake and norp to and modified some of their files You will need 43 chain parts for the Z and Y axis, and 20 chain...

Max's colorful plastic building block is a small brick-shaped structure.

Instructions Select from these options: Base Diameter Increase Percentage: 10% Base Type: Rounded Auto-Fit Font Shift: ON Font Shift Percentage: 7% Text Message: MAx Wall Thickness: Standard Height Adjustment Factor: 33% Character Size: 25 Font...

... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: font_spacing = 1.61 font_scale = 2.1 word = Max pen_length = 90

Customized Version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the Following Options: BlockWidth = Two Name is Max BlockLength is Six

... ... https://www.thingiverse.com/apps/customizer/run?thing_id=52734 Font: write/orbitron.dxf stick width set to 9 Font thickness set to 5 flat bottom mode engaged font size set to 10 stick thickness set to 3 message reads "Max" hole radius set to 3

... was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=45576. ...To customize, set "word" to "Max Fienman," adjust font spacing to 0.81, increase font scale to 1.8, and set pen length at 130.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following settings: Block Length is set at 6 units The name has been customized to MAX Block Width is precisely 2 units