ender z axis 3d models

Changing the bed plate (between glass, magnetic, etc) and/or nozzles will need recalibration of Z axis. This mod allows the Z-axis sensor to be moved up and down by +/- 2 mm without adjusting the 4 screws under the bed. ...It is equivalent to...

This is simply a Z axis mount designed for the Ender 3 to allow the use of stepper motor dampeners. The original mount was flimsy and only supported one side of the motor. I realise its unnecessarily thick in most places but, hey, why not. I always...

Check out this working design on Thingiverse: https://www.thingiverse.com/thing:3245255 https://www.thingiverse.com/thing:3271077 Z-axis damper support: my own design. The Z motor isn't the noisiest, but the damper also stops small jams in vertical...

I tuned original because it not worked for me. ...I have different distance between frame and motor. It's model can help to fine tune your Z-axis motor position.

I remixed the original M5 Z Axis bar wire guide because I want to use M5x20 screws with Phillips head. I Moved the screwholes more together and made two big washers. ... Now it works fine for me!

I designed these clips to enhance the Z axis tensioner's ability to prevent table drop when the steppers are turned off on my Ender 5. They closely resemble bowden clips used on extruders and hot ends, but with a few key differences. These clips are...

The trick behind this, and how it doesn't need any retract/deploy mechanism, is that the Ender 3's X and Y axes can move the nozzle outside of the bed region, allowing the Z axis to go below the level of the bed. This makes it possible to mount the...

Currently using with this bed: https://www.amazon.com/gp/product/B08P4YJ4QK/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 I plan to make another that doesn't require me to move my z-axis endstop from the side to the front but it's working well...

I've scoured Thingiverse for Z-Axis knobs with unique features in mind. Specifically, I sought out a couple of key characteristics: first, threaded engagement with the z-rod instead of just relying on push fit so it could effectively turn the rod and...

... https://www.thingiverse.com/thing:398515 The bed leveling very cumbersome with the stock springs, and the bed can jump down from the screws. ...This limit switch mount makes the whole Z axis lower with 4mm, so the springs can keep stronger the bed.

Support Unavailable Resolution 0.2 Z Knob Offers Advantage The longer screw inside the Z knob, measuring 12mm, provides a benefit when paired with a Z motor damper. This setup lifts the motor and rod up by 1cm, enhancing performance. Damper Bracket...

Actual Z axis knobs to fit this are here https://www.thingiverse.com/thing:5147667 Z axis control knob. Revised design from original uploads. new base design prints better and looks better too. Gives users a knob to manually turn the lead...

I realized I wanted to have a cable chain for the z axis and for the x axis, meaning I needed some kind of joint between them. With the newly freed spot where my extruder motor once was, I had the idea of mounting it there. Then I realized I had a...

These are Raspberry Pi camera mounts for the Ender 3 series of printers

I wanted a fixture which does not allow "wrong" placement on the axis. There is virtually no play when screwing it in. ...no support - fully parametric

I wanted a fixture which does not allow "wrong" placement on the axis. There is virtually no play when screwing it in. ...no support - fully parametric

I mounted a second Z motor, so i need a mount usable with T-Nuts. Printed with Formfutura Carbonfil PETG. ... Thanks for the original design !

Модель для крепления концевика оси Z, без качалки Для установки необходимо повернуть кнопку концевого выключателя, удалить качалку и установить на новом креплении

Drill out the limiter switch holes to accommodate them properly. ...The z-brace will not move without its limiter stops functioning correctly.

It's designed to match the height of the 20x20 profile and can be secured using a washer, an M5 hammer nut, and a leftover M5x8 bolt from the Ender 3 parts bin. ...Nevertheless, two additional M4 screws and their corresponding nuts are still required,...

As this project continues to evolve, it's clear that some adjustments were necessary - in my case, cutting a small corner after printing was required to ensure the x-axis could move freely. ...A photo demonstrates the need for this modification, which...

Just another cable chain for the ender 3. It doesnt work with the original extruder. Even if i would make it working, there is not enough space to handle it. But with Bondtech it works fine. Some others maybe too, but the original doesnt even...

This consist of 2 parts that will snugly fit on the upper side of the z screw (see photo). No more wobble and this improved my print quality. I did it in PETG. There is a small gap so the screw can move a tiny bit but never like before the mod. ... 2x...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

I desperately needed a mount to securely attach my Nikkei extreme camera to the Ender 3 using a clip-on design, but an STL file was nowhere to be found online. With no other option left, I decided to take matters into my own hands and create one from...

The two small screws are reused from removing the flexible base from the camera, and I used one random screw about 12-16mm long to hold the camera mount onto the clip / Ender 3 mount. Webcam:...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

I needed a mount to attach my Nikkei extreme to the Ender 3 using a clip-on, but after searching extensively, I couldn't find an STL file anywhere, forcing me to take matters into my own hands. Having only owned a printer since February 14th, I'm...

This is an improvement for your Ender3 if you don't have (yet) auto bed leveling. ...With this piece you can adjust the end zero point easier.

Modified the following: https://www.thingiverse.com/thing:4441076 To fit within screw holes already built into the frame railing. Used M5 screws 15mm long. Added design with no bearing. All credit goes to @Ziggi42. ... Thanks for the design.