ender v3 v2 3d models

Works for Ender 3, Ender 3 pro, Ender 3 V2 and other printers that uses 40mm aluminium extrusions on the bottom.I have designed Ender 3 anti vibration feets with stock bed springs. But it's a bit too wobbly so I decided to use Ender bed silicone pads...

A side-mounted spool holder for the Ender 3 v2. Will most likely also fit the original Ender 3 and 3 Pro as it just needs the 40x40 extrusion behind the left of the machine to support it. This holds the spool directly left of the extruder inlet...

Based on MartinDubois' project (Tool holder for Ender 3 v2) I made some changes to add a USB adapter holder. ... The spatula and USB adapter holder is placed on the horizontal frame of the printer and is not disturbing at all when printing, while it...

Also my calipers didn't fit right :) My model is tested with Ender 3 v2 only, without the right side display, because mine has been moved to the left. ...Also, my printer is raised because of the improved cooling, otherwise the whole thing would be too...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-orientated for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

I recently bought an Ender 3 V2 to start exploring the wonderful world of 3d printing, but I live in a studio, and my printer is located right beside my desk and around 3 meters from my bed. The Ender 3 V2 is VERY SILENT, so I didn't have any...

They fit the end of a 20mm European extrusion on the left side of the Ender 3 V2 top rail. The filament guides use a standard pressure fitting and a 60mm length of 4.00mm OD PTFE tubing. There are two models of the filament guides, one with a tang...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-oriented for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

Solid feet for the Ender 3 v2, problably other Enders/printers as well, fits all 40x40 profiles. 43mm high, 20mm wide, (20x20mm wide at the bottom). I made these to make room for larger PSU and Motherboard fans. Remove the orignal rubber feet...

Filament guide for Ender 3 V2 (maybe it works also for the other Ender 3), it simply snaps above the x axis motor without any screw. The bearing (is the one of the stock extruder) snaps easily in place without screws and should move freely. It must...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

This is a simple cover for Ender-3 V2 LCD display. The [Creality Ender-3 Logo](https://www.thingiverse.com/thing:3078936) on it was made by [tom666](https://www.thingiverse.com/tom666/designs). Thanks to...

Filament guide for an Ender 3 v2 printer. Most likely works with the original Ender 3 however it hasn't been tested. Sized for a 608 bearing and a m6 x 25mm bolt. To fit properly, the bolt head for the upper Z carriage roller must be on the...

Another filament roller for the Ender 3 V2, picks up on the existing bolt holding the roller on. Requires 1x 608 bearing (22mm O/D) Use a brim & 100% fill to print the spindle, the brim edge acts as a stop when inserting it into the bracket. ...

Filament Arm for Ender 3 V2: -will keep your filament away from the leadscrew -no support needed -no bed adhesion needed -10% infill is enough -friction fit (dimensional accuracy differs per print/printer, i am not to blame if it doesn't fit well)

Tool holder for Ender 3 v2. Slides onto the upper rail. Holds a pair of wire cutters on the end, plus tweezers, a wide spudger, 2 SD cards, 2 microSD cards and USB stick. ...I would recommend printing with support for the wire cutter holder

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

Feet for ender 3 v2. They will give you extra 15mm ground clearance. They do not stick though, so if you lift the printer up they will fall. Also the rear left leg would normally colide with the psu cover, because of the hook for the cables. ...I have...

FOR/ PARA --- ENDER 3/pro/v2 not big deal its a filament guide no need screews yust plug and play ball bearing needed 7.9mm inside 22mm out ------------------------------------- no es la gran cosa es una guia para filamento colo colocar y usar se...

After making Ender 3 v2 ikea lack, I wanted to take the motherboard out and made a simple drawing compatible with the motherboard in Fusion 360. I used a fan size of 80x80mm in a drawing. ...cover screw holes were created for 3mm bolts.

One-piece design for Creality Ender 3 V2 inspired by the frame's V-slot rail style. Compatible with tie-rod frame support brackets. ... Multiple mounting possibilities - Two screws M5x10 and M5 T-nuts - Vertical cable tie holes to attach to bracket...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... I bought this kit on amazon:...

This is a 53.5 mm diameter dial gauge holder for the Ender 3 V2 printer. It sits on top of the extruder fan housing and attaches to the extruder with an M8 x 25 mm screw. The bracket is of the clamp type. ...For the comparator there is a M6 x 60 mm or...

Designed up this Ender 3 V2 LCD Support to move it closer to the body and save space on printer place. ... Printing: Print it in horisontal with supports (minor needed) with 50 degrees touch base only PLA (20% infill) 210º Extruder 60º Base ...

Ender 3 V2 Tension Caps Cap #1 goes in the front facing slot Cap #2 goes in the slot above the LCD screen May be a little snug, so you may have to wiggle the legs a little to loosen them

Super Basic part to cover the screen on the new Ender 3 V2. Parts rest on the outer frame of the screen not the screen itself. ...I have both the plain screen cover and the cover with imperial logo that I printed for myself here.

Este es una adaptacion de este modelo https://www.thingiverse.com/thing:5260591Los eslabones no son mios, El credito de los eslabones es unica y exlusivamente de https://www.thingiverse.com/arek_r1/designsLo unico que hice fueron unos pequeños...

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this I created my own. ...It's still very flimsy and not the greatest especially the clips on the side because they don't hold onto the screen too well.

Yet another fan guard for Ender 3 V2. I use it alongside my fan duct: https://www.thingiverse.com/thing:4754118 The inside cone is particularly wide to correspond to my front remplacement fan that has quite a wide center disk (12mm). ...I'd suggest...