ender v2 vs pro 3d models

Screen mount for the BTT HDMI5 screen. Fits most Creality type bed slingers. The larger top part will need some supports for the inner part. To install - Place the screen into the back section first (screenbottom.stl). The back piece...

I was not a fan of the slide on attachment (even though it is very secure) I have lights that attach on the ends of my machines, top taller screws and many other reasons a slide was not usable. So I modified it to just pop on and be held in place by...

Remix of: https://www.thingiverse.com/thing:4634481 This design worked really well until I updated my fan shroud to a 5015 front mounted fan. Then I was running into the issue of the fan knocking against the camera arm during the bed leveling...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Didn't like niches in original z-axis stabilizer so I designed a simple cover to hide them.

A simple bed-level test to make sure that your printer is leveled correctly !!only print one layer!!

I built a mount for some Foscam C1 camera's which were lying around at home. Its a sliding design so no screws needed. Simply print, open the top rail connector and slide it in, thats it! You can print either standing up (will require greater time...

Base Remix to fit TECKIN camera remix from https://www.thingiverse.com/thing:5215742

I made the bin shorter in length so that two bins (for two different kinds of filament scraps) could fit by one side of the ender3

This is a remix so it can b used with second Z Axis motor (does not have V-slots). Use with stock screw, and add 2pcs of M3x6 to motor screw in. ...

I designed this stabilizer for the shaft of the z-axis. This is canceling swinging. ...The bearing is very stable and there is nothing preventing it from turning.608 Bearing,2x t-nuts,2x M4x12 screw,2 M2x5 screw, If you think that the bearing is stable...

Remix of TheViralDIY's design just to remove the text on the filament holder. The text on the original was not e.g. the designer's attribution, it was purely decorative (the name of the printer). ...I don't particularly need the text there, and removing...

<p>This attachment is to be added to a model of your choice. ...For example, you could add this attachment under a bench, logo, and be able to use it as an LCD knob.&nbsp;</p><p>The only limit is your imagination.&nbsp;</p><p>&nbsp;</p><figure...

<p>After I convert my printer to direct drive my extruder cables were touching the Z rods. I don't like cable chains so I need a solution for cable management.&nbsp;</p><p>The guide has a 90 degrees angle in order to better route the wires and it is...

added basic slit for the raspberry pi camera cable

I hacked together a makeshift rail mount by snagging one from rdprosser, tweaking it to fit my needs, and chopping off some extra length at the front for better clearance. The Y-axis was constantly bumping into it, causing more problems than I...

This is a remix so it can b used with second Z Axis motor (does not have V-slots). ... Use with stock screw, and add 2pcs of M3x6 to motor screw in.

Improved and enhanced mount designed for Creality filament sensors. This new design enables the filament sensor to rotate freely, effectively preventing any tangling or snapping of the filament. I thoroughly searched through Thangs to find the...

<p>This is a remix so it can b used with second Z Axis motor (does not have V-slots).</p> <p>Use with stock screw, and add 2pcs of M3x6 to motor screw in.</p> Category: 3D Printer Parts

This is the exact same but there is a rail mount so you don't need screws.

I have heavily remixed the original. I added multiple features and even added a logo. I hope you like it In case you are wondering there is a hole thru the arm. its added in case you would like to put a metal rod thru it to prevent from sagging, it...

All the Creality printers come with this ugly QR Code on the printer, mine was even peeled up in the corners. This simple <1h print covers it up. I made 2 versions; mine fits the 41.5mm one but maybe your printer isn't too precise and you need the...

It's a situation requiring BTT SKR V1.4 technology and UPS 24v V1.0 equipment.

Replacement for stock parts that's cause lack parallelism of lead screw mechanism relative to frame , and z wobble effect in result. ... Also compatible with frame vslots that help to make fixed lead screw / frame geometry.

Newly designed filament guide installed with small bowden tube + X-axis cable holder. Designed in Inventor. ...

I modified the spool holder so that i can have one filament spool in use while preparing the next filament. ... You'll need: 4 x 608 bearings 8 x M8 washers 1 x M8x180mm threaded rod 2 x M8 locking nuts Other than the 2 thing downloadable...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/5MwPqRbmmnI

I put warning sign on the motor cover so maybe my 3D Printer could be a little bit more stylish. I have not actually printed this thing though, I will be doing that soon. UPDATE: 4/7/22 I have printed the sign and it fits perfectly on the x-axis...

just tried to remix this to remove the buck converter space as it wasn't needed, it isn't perfect but has worked well on my machine