ender s1 pro vs ender 3 v2 3d models

... Good for ender 3, v2, or any other printer that uses same profiles as Creality. Left side designed to be exactly same length as the aluminum profile, and right side sticks out a bit. 12cm in length, verify that it not interferes with the z axis.

Here's a Wyze Cam V2 mount for the Ender 3 that mounts behind the control panel. You'll need to get slightly longer bolts. It does get in the way of the control knob a lil but you don't have to stretch you wrist around to get to it. It has wire clips...

I was looking for a filament spool holder for my Ender 3 S1 to keep the spool centered during prints. I couldn't find one like I was looking so I've designed this one. Also works for Ender 3 v2 (I don't know about other versions though). This a...

I designed this by using solidworks, You can use the stock of bolt and nut from ender 3 PRO Y belt. Advantages: Anti-electric shock Big diameter get more stronger to tension the belt Cover all rectangle shape of frame make more stable and...

Noticed kevCarrico's turntable for some other printer and had to make my own version for the Ender 3 S1 & S1 Pro.Uses 1 ballbearing 5mm center x 10mm outer ring in the TTbase, and 2 magnets 5x5m.All is press fit no glue.Link to kevCarrico's Turntable...

I'm grateful to Blinkii from thingiverse.com for their design of thing:3178072, which I used to upgrade my Ender 3 Pro. What I was looking for was a design that would seamlessly integrate with the upgraded features of my printer. Since the Y-axis...

For example: https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offset https://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...

Extruder wheel for Ender 3 S1. ...Also add model for taurus cooling system.Video - https://youtube.com/shorts/ljr8Pbum4LY

best profile ive found for the ender 3 s1, takes care of stringing and much better quality

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, (for use with anti backlash nut, mounted at the bottom) no need for extra hardware. ...The screw mounting hole is at exactly same level/height as original one on the other side ;-) enjoy Print: ...

Fits well with the following mods: Motherboard cover: https://www.thingiverse.com/thing:4653994 Ender 3 v2 PSU cover + cables cover (80mm fan): https://www.thingiverse.com/thing:5778820 Ender 3 v2 Front Power Switch Mod:...

This is a snap on fit tool holder for the Ender 3 S1 and S1 Pro. Small portion requires supports, see image for details. It holds all the tools that come with an Ender 3 S1 and a few extras too. All tools are held away from the gantry so they don't...

Download latest version here: https://www.printables.com/model/178884-ender-3-easy-space-saver-control-mount-easy-print (now maintaining it on Printables...) I wanted to reduce the footprint of my new S1 and made a new mount that moves the control...

I found the original design to be a bit tight in that area for my Ender 3 v2 model, leading to unwanted strain in the base.Redesigned the primary load path within the base and tried to get rid of as much excess material as possible, resulting in a...

It can be really annoying when the display of your Ender 3 (Pro) shines brightly in the dark. Especially at night, it can be quite distracting. To avoid this problem, I created a simple display cover or screen protector that you can place over the...

"Remix" to include different thickness .stl files. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 100% Filament: Generic PLA Any Post-Printing ============= Mount instructions (same as...

I needed a large drawer for the left side of my Ender 3 Pro. I printed these dual drawers for the front of my printer: https://www.thingiverse.com/thing:3416444 Then I upgraded to the Rear Electronics Case from Teaching Tech: ...

Needed a big drawer for the left side of my Ender 3 Pro I printed these dual drawers for the front of my printer: https://www.thingiverse.com/thing:3416444 Then upgraded to the Rear Electronics Case from Teaching Tech:...

The corner on the Ender 3 S1 differs from the Ender 3 S1 Pro model and has a very different design over the pro model. If you mirror it you should get a right corner. The tear shaped holes indicate which way is up. There are two variations. A...

After having my Ender 3 V2 for over 2 years now i ended up getting into Klipper as my firmware of choice. this led to me being able to print at forever faster speeds and far more than i thought would be possible. But it did highlight some area's to...

If you want a single blower ring the Ender 3 Vent ring and Ender 3 Vent ring 2 By: Filboy should work for a sing fan setup. if you want it on the other side if you mirror it in Cura it should go on nicely. should also work. ...Please let me know how...

Many thanks!https://www.paypal.com/paypalme/mrhuy01081999 Description This is an upgrade kit of the Ender 3 V2 hot-end module. Consists of:- A mount of direct drive BMG BondTech extruder kit and stepper motor NEMA 42x22 0.8A.- Mounting and...

A simple but effective webcam mount designed specifically for the Ender-3 S1. Simply slides on to the X gantry, no tools or disassembly required. V2 changes: added cable tie holes. Also included is a threaded knob to match any webcam with a...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

This is a small cover that helps keep cables inside the aluminum extrusions on an ender 3 to help give a nice and tidy look. I fit a 3.5 mm cable with the clip over it, I'm not sure how much bigger you can go. Printed with PLA. It just slides in from...

... ...Now thicker base sround the Dial stem, And can secure Dialindicator with a 3mm screw. Clips on over heatblock fan cover, should be removed after use as it covers part of the fan intake.Printed in PLA+ 20% infill on a Ender 3 S1 Pro

Remixed this from an Ender 3 Pro LED Light bar holder by scottyujan. I just found it to be too short for the LED light bar I had kicking around. Extended the ends to support my 30CM bar. ...Tucks neatly under the S1 filament runout sensor.

Hey all.. ...i remix this oreo knob for my new Ender 3 S1 ! This oreo knob is a must have for all! ...enjoy !

Just a mix, minimal scraper holder for Ender-3 s1 for spool arm https://www.thingiverse.com/thing:5217972 mixed with https://www.thingiverse.com/thing:5318707