ender s1 plus upgrades 3d models

152x22.8x15.9 Print two, or resize length in slicer. Fits tight. ...Be careful applying force to lamp.

Extended to fit my own LED light

Customized version of https://www.thingiverse.com/thing:3141591Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3141591

This is not a remix. It may look like others on this platform but it is a complete redesign from the ground up. Advantages over others:- 1. It is extremely accurate and will fit your sprite extruder perfectly if you have your printer set up...

After installing the factory light bar I could not use the tool holder that I downloaded from here, so I decided to create my design my own. ...This is my first time uploading on this site

This is a holder for the Ikea Led stripe. It holds two of them. ...Easy to print and install.

With the part cooling fan now mounted at the front, it is not easy to view the prints especially if you mounted at overhead LED light like I did. Thus, I designed a Nozzle LED Light Strip holder. This will enable you to mount a strip of LEDs that...

Remixed from:https://www.thingiverse.com/thing:5511795

These height adjustment feet (30mm to 40mm) fit between the original rubber foot and the frame in the original screw holes. Unscrew the original rubber foot from the frame.Attach it to the new “Foot” using the original M4x20 screw.Attach the new...

Rigid sensor mount input shaping

First remix, I used TinkerCAD to modify the USB holder and replaced it with a slot to hold calipers which wiped out the original two slots in that location. ...And of course I added my branding.

Yes you can now include the stock plier from Creality. I know it's not perfectly designed so I had the STP uploaded. ...You can now edit it to fit your own tools.

Two M4 threaded nuts are required, along with two M4x12 screws. ...Additionally, one Ender 3 LCD display unit, complete with mounting screws, is necessary. ...Furthermore, two LCD cables will need to be procured for this project.

amazon.com/WINSINN-Blower-Upgrade-Bearing-CR-10S/dp/B08R9J189W/ref=sr_1_8?crid=2RNQRGN86YQMX&keywords=ender+3+v2+blower+fan&qid=1693871980&sprefix=ender+3+v2+blower+fan,aps,208&sr=8-8 Special Slicer Instructions: -Non CR/BL standard shroud can be...

This bracket has been designed to replace the stock bracket that comes with the Ender 3 S1, it comprises of three prints. The main bracket that screws in to the same holes as the stock bracket with the stock screws. There is also the lid which is for...

Uploaded BMG mount for standard V6 to account for the BLTouch Recreated in fusion for my Ender 5 Plus, as Creality has slightly modified their hotend carriage. It should fit the other Ender 5, Ender 3 and CR10 series as well as they all have...

"S1 Pro Filament Guide - Main Support (M10 PTFE Fitting)" - allows the use of a 10mm thread PTFE fitting so you can run a bowden tube between the main support and the filament dryer. “S1 Pro Filament Guide - Main Support” - No bowden tube with this...

I am surrounded by Ender 3 V2s in my office and I wanted to see if I can find a way to make them look cooler, rather than be surrounded by a bunch of black machines. After searching for something already made and not finding anything I took it upon...

FIRST OF ALL: You are not forced to print both part. You can keep one of the two "stock". The cooling duct is based on the "Stock Creality Sprite Fan Double Duct" from Sorkin and adapt it to fit a blower fan 5020 24VDC on it. It is super quiet and...

hi everyone this is the first upgrader that i thing will be good fro your Ender 3 skr 1,4 t tmc 2209 tft 3.5 v2 titan direct extruder and cable management (dsub 25 pin) for d sub you need to print it with nozzle 0.4 layer high 0.2 all the rest is...

For example:https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offsethttps://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...

This is a remix of Minus97's display Bracket. ...The bracket itself is away from the printer instead of attached to it. It works for the ender 3 s,1 the s1 pro, and s1 plus. ...I printed it upright and it worked out great!

This modification works incredibly well to guide filament from a Sunlu Filament dryer. ... You will need; 4 - 4mm x 14mm machine bolts (Philips head) 4 - 4mm x 12mm machine bolts (Philips head) 4 - 4mm flat washers 8 - 4mm nuts...

Why creating a bottom plate when there is already one? Well, the original is metal. This is more likely to responde to vibrations and magnify them, making the printer louder than must. I also added different low noise fans to the motherboard (80mm)...

... infill is recommended, with 100% on the duct. No supports are needed except for the direct drive mount. I always raft the parts. After the direct drive upgrade, you can reduce retraction significantly or entirely if you don't mind some stringing.

Includes a reprap 12864 display mount, drawers, Z rod knob, encoder knobs in 2 styles,a 4040 V-slot cap and a fusion 360 file for all of them. DISPLAY MOUNT IS WIP - You may need to tune the dimensions in the fusion file to match your printers...

Includes a reprap 12864 display mount, drawers, Z rod knob, encoder knobs in 2 styles,a 4040 V-slot cap and a fusion 360 file for all of them. DISPLAY MOUNT IS WIP - You may need to tune the dimensions in the fusion file to match your printers...

Creality sonic pad handle for Ender 3 S1 (more place for cable)

Netatmo Smart Smoke Alarm spool holder for Creality Ender 3 S1. Category: 3D Printing