ender pro 4 3d models

This is my case for Ender 3 Pro and 3D Printer Motherboard BIGTREETECH SKR V1.4 compatible with thing 3416444 (Creality Ender 3 Pro dual drawer). Also compatible with standard parts Ender 3 Pro This version saves space for these boxes. The...

You will either need a USB extension cable for it or a USB stick where the case for the USB is a fair amount of distance back from the actual connector. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution:...

I went with a 4 wheel carriage for my ender 3 pros direct drive conversion. It is a little wider than the OEM 3 wheel plate. So I remixed another mount. I had to make it a little wider and then I reinforced it in 3 areas a little more. I printed it...

While my Ender 3 could manage the bridging of the original file, it was kind of messy and needed to be cleaned up. With the added walls underneath, the only supports needed for this is along the left side and left back corner. Word of note: If you...

While my Ender 3 could manage the bridging of the original file, it was kind of messy and needed to be cleaned up. With the added walls underneath, the only supports needed for this is along the left side and left back corner. Word of note: If you...

This is a quick remix to add the facility to squeeze a 40mm cooling fan to the outside of the case as we know the Raspberry Pi 4 runs hot. I much preferred this design as it allows Draws to be fitted, adds easy access for the LCD Ribbon cable, as...

The Raspberry Pi 4 sits on raised mounts fixed with screws and allows for venting underneath. It was printed base down as per the models within the pictures. Please share your prints and comments. ... Thank you to Phobus11 for your expert...

This is a simple remix of drakaz design adapted to the Raspberry Pi 4 Model B (original was for Pi 3). ... I also added 2 holes in the back to integrate: - a push button to start/stop the Raspberry Pi - a Led to have a feedback on Raspberry Pi status I...

This is a simple remix of [drakaz design](https://www.thingiverse.com/thing:4417133) adapted to the Raspberry Pi 4 Model B (original was for Pi 3). ... I also added 2 holes in the back to integrate: - a [push...

Box pro základní desku Bigtreetech SKR 1.4 vhodný pro tiskárnu Creality ENDER 3 PRO. Nachází se vlevo dole Po tisku přidejte matice a šroub M3 šroub pro zajištění horního krytu a 30mm ventilátor k pravé stěně. Box for motherbase Bigtreetech SKR 1.4...

Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 20 Infill: 10 Notes: Pretty easy to print design. The tolerances are TIGHT, so you make need to do some minor cutting in your...

I'd like to thank both of you for creating a remix of the Geekworm case Raspberry 4 wall/desk mount and the Ender 3 Pro rail mount slider that fits perfectly in one profile slot. This clever design mounts the RPI4 securely inside its case to the...

Ender 3 Pro Front Case for Raspberry Pi 3 & 4. You can also check Ender 3 Pro Front Case for EZBoard Lite, SKR Mini E3 and Original Motherboard here: https://www.thingiverse.com/thing:4285759 Please accept my apology for any misalignment from my...

It is meant to sit in between the LCD and y axis extrusion, like the Ender 3-V2's tool drawer. The Pi will sit upside down in the case, so that print debris won't get in the way. And there is mounting for a single 30mm fan. It does include space...

Still a rough work in progress while I dial in tolerances. ...I liked the original design, but I wanted a honeycomb mesh, and a Pi 4 slot, so I added them!

Still a rough work in progress while I dial in tolerances. ...I liked the original design, but I wanted a honeycomb mesh, and a Pi 4 slot, so I added them!

I also added some holes for ventilation between them. I was print them with support from build plate and it turns out perfect, but I think it would not be necessary to add the support everywhere. This is a remix from...

I could not find the perfect shell for my taste and need (fitting it upside down to the lower side rail of a Creality Ender 3 Pro to run octoprint), so I took the most good looking I found IMHO, and tweaked as needed. Here are my edits: - added...

Remix of Raspberry Pi 4 Case by anjanathisal, I added mounts on the side so you can clip it to the bottom right rail of the Ender 3 / Ender 3 Pro with ease. ... Also added air holes in the bottom and back for improved airflow, as well as a larger...

This is a remix of the LCD Enclosure by @eoyilmaz. I adjusted the number of ports available, also lowered the PI location so that I could add a mount for the fan. I also added posts for a Buck Converter. **Note: I have not printed this yet,...

3-D bargains https://t.me/chollos3dMasQFilamentos ENDER COMMUNITY CREALITY https://t.me/CrealityEnder3Original -Adjusted the impulse to impress. -Improved Smoothing: smoothing flow, percentage and its accelerations. -Improved top and bottom layer...

I found the prior model to require much longer screws than I wanted to use to connect my Raspberry Pi to the lower piece. This rework makes the columns that support the pi larger diameter so the screw head can go inside the column and shorter screws...

I wanted to mount my RPi 4 running Klipper where the touchscreen After printing it should slot into the touchscreen mount just fine - the Pi can be mounted using M2.5 screws or standoffs Enjoy!

I'm looking for a way to integrate the SKR-1.4-Turbo board into my Ender5Pro case without any issues. I designed a custom mount that fits perfectly in the same spot where the Creality silent board normally sits. To secure it firmly, I'm using a thick...

WORK IN PROGRESS ====== A custom bracket holds a Raspberry PI and an SKR 1.4 board securely inside the original Ender 5/Ender 5 Pro case. I plan to add a blower fan in a future update to keep the PI cool, but you can also use any typical raspberry...

Items on Tinkercad here: https://www.tinkercad.com/things/dPB67qKLRoX This is a combo Raspberry Pi 4, Picam case and mount for the Ender 3 Pro (or other V-slot printers). I'm including the Tinkercad so you can move the mounting plates to other areas...

The search led me to https://www.thingiverse.com/thing:3741488, a clever idea that caught my eye, but unfortunately, it only fits the Ender 3, not the Ender 3 Pro model I own. Naturally, I had to make some adjustments - after all, this case needed...

I used the following screws: * 8x M3X8 countersunk for the bottom and left and right * 4x M3x15 Flathead for the top * 4x M3x8 for mounting the SKR board to the base I''m not completely satisfied with the case fan design as the Ender 3 Pro has it on...

Even at this resolution it still came out great. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: YesResolution: 0.2 Infill: 20% Filament: Creality PLA Black Notes: See the screenshot for slicer settings. I've...

What a lovely idea - but it only fits to an Ender 3, not an Ender 3Pro... Of course I needed to change that :-D The design was made in Blender and I don't know anything about Blender. So I rebuilt the complete case with minor changes in Fusion 360. I...