ender cr 10 v2 3d models

https://www.thingiverse.com/Coolcrawler_/about Print Settings Printer: Creality CR-10 Rafts: Doesn't Matter Supports: Yes Resolution: 0.1-0.2 Notes: Post Processing: Once you are done printing, clean both the base and arm. Print at highest...

UPDATE 9/27/17: I added Creality_CR10_Extended_Extruder_Arm_2 and it should be more accurate to the original I find the extruder arm for the Creality Cr-10 to be too short and the spring too strong for my weak and scrawny "muscles." So, being the...

UPDATE 9/27/17: I added Creality_CR10_Extended_Extruder_Arm_2 and it should be more accurate to the original I find the extruder arm for the Creality Cr-10 to be too short and the spring too strong for my weak and scrawny "muscles." So, being the...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire...

When loading filament into the CR-10 v2 from the top the filament can put stress on the filament sensor. The filament rubbing against the sensor entry has the potential to leave debris that can block the sensor and can sometimes squeak. This pulley...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire should...

Remix from Z Sync Tensioner for 852mm belt for my CR-10 V3,i made it longer for my need,so I can set different belts if i want. ...:) Original file: https://www.thingiverse.com/thing:3988905

The biggest improvement came from adding dual-z upgrade to my CR-10. Most likely acceleration and jerk values have to be changed (slower). Let me know if you have any questions. Update: 02/22/2019 Added "BLTouch_Ender_3_Flexion_E3D_Mount_Best_Fit"...

==================================================================== This is a standalone conversion kit to remove the need for the separate control box on the CR-10 V2! I hope you find this conversion useful and that it works properly for you. A...

This is a set of clamps designed to replace the hinged metal glass clips included with the Creality CR-10 V2/V3. These clamps will hold your glass in place with the added benefit of not obstructing **any** of the print surface. Never worry about...

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.This model isn't easy...

I remixed the Wyze v2 camera mounting plate from fuchsr but made it fit the Creality CR-10. There is no shortage of existing mounts for this camera/printer, but I wanted one to mount to the gantry. I found myself having to frequently reposition the...

Complete set of slot covers for the base of the Creality CR-10 V2, minus the gantry rails - they weren't added for style, but to keep filament from getting stuck in them. The flange extends all the way to the center of the rail, so nothing gets...

Complete set of slot covers for the base of the Creality CR-10 V2. Does not include the gantry rails. Didn't do it for looks, but to keep filament out of the rails. The flange extends to the center of the rail so stuff doesn't get caught between the...

The direct extruder connector that came with my Titan direct drive feeder kit for the CR-10 v2 was poorly machined and would not screw in. I decided to try designing a replacement that I could print in PETG. Since this part is at the cool top of the...

I looked around for a mount to test the Biqu H2 tool end on my CR-10 V2, but decided to create my own. I designed this based on the Biqu H2 dimensional step file available on Grabcad and verified the measurements once the actual tool end arrived in...

This is a set of brackets I use to mount three 15mm square LED light bars on my CR-10 v2. Edit: I was asked which lights I am using. Here's the link: https://www.amazon.com/gp/product/B06Y3YG8PP/ Two of the "20mm Extrusion Brackets" will hold a...

To secure it, I used a M4 bolt and T nut, both of which appear to be extras from the CR-10 V2 kit. This simple modification keeps the build plate power cord from dragging against the frame, potentially extending its lifespan. If you're planning to...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

I do plan on throwing a TriangleLabs BMG v2.0 onto my CR-10 V2, so I'll need a riser at that point. I might revisit the design and make the tunnel thick enough to use bowden tubes with pass-through bowden connectors instead of the bump-stop ones...

CR Touch mount for this particular remix of the Satsana Fan Duct

I made this to attach a 1" travel dial indicator to my Ender 3 V2. It requires a CRTouch bracket (though not necessarily the sensor itself). It mounts above the bracket using the brackets mounting bolts. The indicator I am using is this one...

I've increased the dimensions of the top bracket and added some more brackets to the bottom (v2).On the ABL mount I've cut out a slot on the top to make the wires fit for a CR Touch. I've also made a slot along the bottom for it's cables to route...

I've successfully created a similar version using free printable parts and standard electronics for my Ender 3, making it compatible with Ender 5 and the original CR-10 (not S Pro). This upgrade isn't as good as established options like BLtouch or...

To Starwars up youre printer. ...Just added a cr touch and noticed the pertaining part of the mythosaur cap getting in the way of the cr hitting the limiting switch. ... So borrowed the Mando bust design en created this one.

Remixed https://www.thingiverse.com/thing:4647793 Added a draft angle to the face that mounts to the stock Ender 3 v2 carriage plate as my Hemera, and therefore nozzle, were not square to the axis/bed. The draft angle "pushes" the bottom of the...

Had some old Flashforge filament spools laying around, however the spoolholder to my creality CR-10 is too wide to accept them. So I made a new spool holder using TinkerCAD that fits the nut from creality. There are other designs for this purpose,...

The CR-10 hotend performs perfectly, whereas I and several others have encountered numerous issues with the Monoprice factory hotend. No additional hardware is necessary. Simply print the backplate with supports facing upwards, as the faceplate does...

CR-Touch mount for Hemera backplate as the BL touch version obscured the cable entry. Also added a support to make the structure more rigid. Mount with a M3x10 to plate provided by original thing:4647793 keywords: hemera mount backplate cr touch...