ender 6 klipper 3d models

My Ender 6 had door hinges that were over countersunk such that the screw bottoms out before they become tight. This leads to the door ratting when printing at speed and causes the top edges of the door to interfere when shutting. ...This is a very...

... ! Just setup my ender 6 and i had trouble and was disappointed by the original fixing of the hot-end cable, so I created one on solidworks. ... The ptfe tube is also better aligned 10/05/2022: Have to test chassis V2 and working on Hot-end V2

I remixed the Fan Shroud for stock fans on this set of BIQU extruder mounts for the Ender 6. I could not get it to slice without holes in it, so this fixes that. ... https://www.thingiverse.com/thing:4893522/comments

... to the inside of the chamber so that you don't need to remove the tube from the top cover whenever you need to remove the cover for some reason. ... ThinkerCad: https://www.tinkercad.com/things/5tmJCcz3k8D-ender-6-diagonal-filament-guide-toward-inside

Bauteilkühlung für den Ender 6 Benötigte Teile: 2x 4010 Blower 1x 404010 Lüfter 4x M2x10mm 4x M2x6mm 1x Kabel für den zweiten 4010er 1x JSTXH 2Pol Stecker + Kontakte Der 40x40x10mm Lüfter kann mit zwei M3 schrauben direkt in das Kunststoffteil...

I made these to be able to easily remove the back glass on the Ender 6 without any tools. You will need 10 M5 x 20mm 0.80 Coarse thread hexagon head bolts for each panel you want to use these on. ... You will need to print with a raft.

I needed a mounting plate for my SKR pico for my ender 6 done! ... Use the M2 screws provided with the motherboard and the original screws that hold the motherboard in place models with and without fan available use 40x10 fan ! Remix from thing:4870104...

I needed a mounting plate for my SKR pico for my ender 6 done! ...&nbsp;<br>Use the M2 screws provided with the motherboard and the original screws that hold the motherboard in place&nbsp;<br><br>models with and without fan available use 40x10 fan...

(https://support.th3dstudio.com/helpcenter/ender-6-5015-ezabl-petsfang-mount/) I have removed the ezable attachment and replaced it with a mount for the BLTouch. ...(Make sure your BLTouch is wired to the main board, I could never get it to work...

BIQU H2 Extruder Mount for the Ender 6 BLTouch supported For the part cooling fan two 5015 radial fans are required For the hotend fan i have used a 50x50x15 fan You can use it with or without a BLTouch... ...[bltouch] y_offset: 25.55

BL Touch bracket for Ender 6 with Micro Swiss NG direct drive extruder. Clears printer belt brackets. Uses M3 screws and nuts. Probe offset: M851 X-48.00 Y15.00 Z-4.10 Credit to DevDav I used his back plate to build off of.

Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...

Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...

*************************************************** Cover Ender 6 mit Alu-Profil Eine andere Version des Ender 6 Covers mit Aluminium-Profilen. Dieses Model ist für den original Ender 6, also ohne die Öffnung rechts für Bowden und KW-Schläuche. ...

1 use: Ender 6 Extruder Repositionig Relocation https://www.thingiverse.com/thing:4762567 Hand Filament Guide Remix Ender 6 https://www.thingiverse.com/thing:4762532 Ender 6 extruder hole cover https://www.thingiverse.com/thing:4790871 Ender 6 Cable...

Beefed up version of the Ender 6 cable chain management for Ender 6 Hotend cables. Big Things I did 1) It now accept 10x11 cable chain. 2) Left openings so there is no need to re-wire everything. (If you get open type cable chain) 2.1) *Must...

... to the enclosure instead of just the wires. This has recessed screw holes so that you can still use the original screws. Print Settings Printer: Ender 6 Supports: Yes Resolution: 0.20 Infill: 15% Filament: Any PLA Category: 3D Printer Accessories

--- Der original Ender 6 Board Blower ist extrem laut. Ich habe den Blower gegen einen Sunon MF50201V3-1B00U-A99 getauscht. Dieser hat 27,5 dB(A) und reduiziert damit die Gesamtlautstärke des Druckers um ca. 9 db(A). Da der Sunon Lüfter 12V...

A simple and easy to print cover for the ender 6 Breakout board&nbsp;this was printed on my stock ender 6 with no support ( you can see the pictures)&nbsp;with Devil Design PETG Dark MetalI printed mine with :3 top3 bottom3 perimeters13% Gyroid...

This is an adapter for the hole in the Creality Ender 6 official lid, that is normally used to put the bowden tube through. This adapter will fit 2 bowden fittings. The 2 extra fittings that come with the printer can be used for this. one of...

More Ender 6 models at https://www.thingiverse.com/vampyrex13/collections/my-ender-6-models. Hardware ------------- • (16) M5x8mm socket cap screws • (16) M5 t-nuts Printing Notes ------------- The model will fit the upper right and...

Only affect the y-axis by 24mm due to the x-axis bracket clearance (based on windisch/BWI Ender 6 model). Light and strong with good clearance and cable management hole! Z-axis height is the same. X-axis is unaffected. I currently use...

I have created a version that is 9.5 mm taller and 9 mm wider than the stock part cooling fan duct to make it work with Showa_211:s Ender 6 Hot end fan shroud (https://www.thingiverse.com/thing:475555) and my all metal hot end from Microswiss. I...

Designed this because my cable kept snagging against the top of my Ender 6 lid. v2 fully covers bolt and bridges the gap between the 2 lids Print Settings Printer: Ender 6 Rafts: No Supports: No Resolution: 200 Infill: 10 Filament: Standard PLA PLA...

Only affect the y-axis by 24mm due to the x-axis bracket clearance (based on windisch/BWI Ender 6 model). My other design, the Aztec warrior, allows more space on the y axis and includes cable management. Light and strong with good clearance and...

This is an alpha version Change log:includes extruders fan shroudadded hole for filament tensioneradditional mounting holes for the extruder for added rigiditymove the mount for crealitys cr touchImportant notethe added mounting holes on the left...

This is an upgrade to the bracket that holds the wires attached to the hotend carriage on the Creality Ender 6. This bracket replaces the stock bracket and mounts using the original bolts. The loom tubing locks in place but is free to rotate as the...

Made some adapter for the Bondtech Lite and Ender 6. This is a fully functional adapter made out of two existing designs, one part is from Bondtech. Since i am absolutely not a designer i am sure i wont win a prize, but hey, its fully functional. ...

... in this case it is as an example, the two available housings in this download are for storage. If you are interested in the dual sensor variant you can check it out at: https://cults3d.com/en/3d-model/tool/ender-6-panel-temperaturas-y-humedad

This is a small less intrusive spool holder designed to fit the ender 6.it just fits standard spools 55-60mm wide so beware when printing this some spools may not fit.uses 2x 608z bearingsyou will need to print with supports for the roller and spool...