ender 6 dual extruder 3d models

Remixed from https://www.thingiverse.com/thing:5571975 to match height and alignment of WINSINN dual gear extruder - no additional hardware needed height is 6mm added countersink for screw holes for mounting to bracket (use 2 original screws)...

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

Firstly, the original design of the extruder cable holder for anybody that upgraded to the dual gear extruder is briliant; simple and effective. However, I noticed that the original design screw countersunk hole is a tad too thick to my liking...

Had wheels, axles and bearings left over from work on this [adjustable filament spool holder](https://www.thingiverse.com/thing:3648130/) and wanted not only to reuse them, but to have a matched upper and lower guide with lower guide at suitable...

for bigger metal extruder

This remix from the original changes the location of the tube hole so that it aligns to the dual gear extruder shown in the photo. The hole placement isn't perfectly aligned, basically eyeballed it but it's close enough since the rubber bushing...

I scanned in the filament sensor and created a shim so that the new dual gear extruder lines up with the filament sensor. Otherwise the filament has to make quite a turn...Which may be fine for flexible filament, but won't work with others. This...

remixed to add dual extruder

Dual extruder calibration test print

This is a remix of Bart-tech3D's Ender 3 Direct Drive Extruder. It's a very simple remix that removes a 2mm section of the model to allow the metal Creality BLTouch mount to be used. The BL touch mount will fill in the removed area of the stepper...

Ender 7 Extruder Fan Duct has a great design. So i decide to re-design the fan duct for E3D V6 hotend in order to fit my X Axis Carriage on my RepRap 3D Printer. You Will need for assembly: 1. x4 2 * 2 mm Blower Fan 4010 screws 2. x2 3 *...

The height is optimized for the CR-10s Pro Dual Gear Extruder linked below. !!! https://www.amazon.com/gp/product/B07SY745CF If you have a different extruder, you will need to adjust the height of the mount accordingly. You will need to print the...

You can find the same extruder on AliExpress using the link below. The mount for the extruder will fit most CR machines, you just have to drill your own holes to mount the extruder as each is slightly different. The original MBOT3D shroud...

Like the title says - a filament sensor riser plate for Creality CR-6 SE for dual gear extruders with integrated cable holder. Helps with the cable rubbing on other parts and getting in the way of the filament. There are few brands of those...

Compatible with Satsana Neo 3 Fan Cage.I used a 23mm stepper (required if you don't want it to hit rail) - I Had to reverse the two center wires on my ender stepper cable (Blue and Green) for this stepper. This one is on amazon for $8.88 at the...

The case has mounting holes for different cooling packages which might come later. __________________________________Required non-printable parts____________________________________________2x M3 nuts3x M3x40 countersunk screws - for mounting the...

I upgraded my Creality CR-6 SE extruder to a dual gear unit from WINSINN that I purchased from Amazon. The same unit is sold under many different brand names. I tried to tag as many as I could. The new extruder is so much smoother and more...

I upgraded my Creality CR-6 SE extruder to a dual gear unit from WINSINN that I purchased from Amazon. The same unit is sold under many different brand names. I tried to tag as many as I could. The new extruder is so much smoother and more...

I designed this to snap on the extruder arm and help guide the PTFE tube with filament into extruder to avoid bending the filament (see picture without the guide) Support needed for printing the PTFE tube guide.

Dual model for calibrating dual extruder printers (IDEX)

Dual Extruder Alignment Verification Test Print.

Glub but dual extruder have fun :3 !

Dual Extruder Alignment Verification Test Printing

... invention. ...This is why I created a simple platform for a filament sensor. It is worth using when a Dual Drive BMG extruder is mounted Slicer Setting: Quality: 0.2 mm Infill: 25% Infill pattern: Gyroid Brim: Yes Temperature: 200/60 Fan speed: 100%

With it being a Ender 3, I was quickly running out of space, so I remixed the following from: Dual Extruder: florentmarulaz - https://www.thingiverse.com/thing:3413260 Dual Spool Holder: ptajdus - https://www.thingiverse.com/thing:3498855 Combined...

To set the length to 7mm, use the following command: M412 D7.\r\n\r\nM412\r\necho: Filament runout ON\r\nFilament runout distance (mm): 7.00\r\n\r\nFor mounting the filament sensor to the extruder mount, you will need:\r\n4x M3 nuts\r\n4x M3 x 12mm...

... calibration model. ...The distance between the lines is 0.1 millimeters. The center is marked with a dot. Print Settings Printer: Creality Ender 5 Plus with Dual Switching Extruder Rafts: No Supports: No Resolution: 0.2 Category: 3D Printing Tests

Frustrated with pneumatic couplings consistently failing to hold retracting settings? ...I was too, which is why I created a solution.

Remix from https://www.thingiverse.com/thing:3833174 I Added some extra support to prevent bending, and also a chain adapter for https://www.thingiverse.com/thing:2920060 Haven't tested yet.

dual extruder for prusa i3 bom m340mm 4 m3 screw nut 4 M510 2 625ZZ 2 MK7/MK8 2 Spring 0.7×4.8×5×6.5 2 Instructions design with solidworks