ender 6 dual extruder 3d models

This extruder offers several key features: - Utilizes the Creality Ender 3 original heater - Allows for the installation of a 20x20x10 mm fan on the heater - Enables the fitting of a 20x20x10 mm fan on the part - Facilitates easy cabling -...

The goal is to improve filament flow for a smoother input into my new Bondtech Dual Gear Extruder. I also observed that the columns supporting the switch are quite fragile, even when printed at 80% infill density. To address this issue, I added...

This is a custom-designed filament mod for CR10s Pro and Ender 3 extruders, compatible with both Bowden and direct drive setups. It optimizes gear-to-filament clearance to minimize TPU ejection near gears. I've achieved remarkable speed gains: up to...

Parts cooler I built for my FT-6 (dual extruder). May also work with the single extruder variant. The duct attaches directly to the fan. If it feels too loose or tight, adjust the scale by a few percent in your slicer settings to fit. Height is...

... I tried using an enclosure while printing PETG the other day, and the extra heat,coupled with stepper current being a bit high on the extruder, caused my PLA print of this mount to melt out of shape!! Going to PETG now.. ... And fixed the current..

Required Hardware: - M4 - 20mm length machine screw - M4 Hex Nut - 16mm OD - 8mm ID - 5mm length bearing - (The two M3 screws that hold the z-axis lead screw nut to the extruder motor mount) Parts: - Mount: it mounts the pulley axle. - Axle: it...

Filament Guide for a CR-6 SE with dual Gear Extruder.It is a Remix from this: https://www.thingiverse.com/thing:4586801Print SettingsPrinter Brand: CrealityPrinter:  CR-6 SERafts: NoSupports: NoResolution: 0.20mmInfill: 10%Filament: Creality PLA...

Most of the filament sensor adapters for the dual gear extruder required adding two longer screws.I designed this one to re-use two 3mm flathead screws from the original extruder, as well as the two screws already used for the filament sensor. I also...

When you install a dual gear entruder you can't use a knob anymore. ...this system enable you to do it.

The extruder is printed with 100% filling in PETG. ...The Y adapter originates from here: https://www.thingiverse.com/thing:1909725

This is a remix of BGDog runout spacer that I simply made work for the ender 3 max. This is my very first creation. Please note I sliced this 2.5 mm BELOW the bed and it worked pretty good. You will need longer screws. Edit. ... Not...

I use my bmg extruder clone with the flipover mount and had space on top. The original chainmount does not allow a chain to the hotend, so i made this quick "copy & paste" thingy to have a sideways mount too. The Corner of the upright...

This is a support arm for BigTreeTech's ZSYong 2 in 1 hotend, designed specifically for the Creality Ender 3. Required hardware includes: * A 5015 radial fan * Four M3 nuts * Two screws measuring 3x25 mm * Two screws with countersunk heads, each...

- Edit 1: Added a second mount file to support the 24mm center-to-center mounting holes on the dual bowden setup Anybody with an FT-5 or FT-6 knows how bad the original ACM extruder mount is. This piece was created to give more solid mounting to the...

Most of the filament sensor adapters for the dual gear extruder required adding two longer screws. I designed this one to re-use two 3mm flathead screws from the original extruder, as well as the two screws already used for the filament sensor. I...

Ender 3 / 5 Direct Drive Extruder DotBit Dual Drive Extruder Setup

This is a support for dual extruders.

If you're working with the FT-6 and have the dual bowden hot end, be aware that the mounting holes are spaced 24mm apart, not 18mm as previously stated. That's all I changed here - simply pushed the mounting holes out by 3mm on each side for the two...

If you're using the dual bowden hot end on this model, be aware that the mounting holes are spaced 24mm apart, not the usual 18mm. This revised file makes just two key changes: it adjusts the mounting hole spacing and removes the ABL mounting holes...

Direct Drive Extruder Filler Ender 6 v2 fix remix

Filament guide for Ender 6 direct-drive or relocated extruder.

Untried yet, a straightforward blueprint exists for the Folgertech FT-6. ...This design is patterned after Michael Foegelle's untested creation found on GrabCad.

a cable support for the awesome "BIQU H2 Extruder Halterung für Ender 6" from wendischb for the original Cable tube the awesome BIQU H2 Extruder Halterung für Ender 6" from wendischb https://www.thingiverse.com/thing:4762042

Compatible with:Extruder :SKU M3205 - Micro Swiss NG™ Direct Drive Extruder for Creality Ender 6 PrintersHotend: Micro Swiss All Metal HotendHotend Fan: 4010Part Cooling Fan: 4010 BlowerProbe: none3D Printer Model:Ender-6

a cable support for the awesome "BIQU H2 Extruder Halterung für Ender 6" from wendischb for the original Cable tube the awesome BIQU H2 Extruder Halterung für Ender 6" from wendischb https://www.thingiverse.com/thing:4762042

... NG Direct Drive Extruder for Creality Ender 6. ... Compatible with: SKU: M3205 (Ender-6 NG Extruder) Use support from build-plate only. Print using PETG, or a more heat-resistant filament. ... MS_NG_ESTEP400.gcode sets the printer E-steps to 400.

Ender 3 Adapter for Secure Mounting of Trianglelab Bowden BDTech Clone Dual Drive Extruder or Similar Models To install the Ender 3 adapter, begin by mounting it to your printer's frame with the solid hole facing upwards. ...Next, carefully slide the...

Hi! ...This is an adapter to fit the Orbiter v1.5 extruder to Ender 6 printer types and others with similar hotend setup. ... The design its not tested yet so any feedback is welcome.

It based on the files from Shaneomac which can find here: https://www.thingiverse.com/thing:5255502.If the extruder is mounted next to the z-spindle, you can mount this filament guide with the original screws.Extruder holder in the pictures:...