ender 5 wiring 3d models

I've been using my Creality Ender 5 and Pro for quite some time now. These machines come with a pretty long PTFE Tube, which sometimes ends up obstructing the x/y axis gantry and causing problems. ...Although I haven't had any failed prints yet due to...

... forth. Keep in mind that the standard wiring on my Ender 5 plus may not reach all areas of the print bed when using this wire guide. I created this because I upgraded to a direct drive extruder, resulting in an ineffective existing wiring setup.

I wasn't thrilled with the appearance of those zipties, so I created some clips instead.

Upon noticing the extruder wires were chafing against the lever following a recent adjustment to the extruder lever, I opted to craft a custom holder utilizing the zip ties provided with the Ender 5.

The major drawback of the Ender 5 (Pro) is its wiring, which appears to be an afterthought. The goal of this design is to utilize the stock wires while providing them with sufficient support, clearance, and tidiness. A key component is the arched...

I got sick of looking at my wires just hanging around and wanted a low profile management system. Not the greatest design but my first. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/5OMwtd6dnkd

This clip seamlessly integrates into the extrusion rails of an Ender 5 Plus and likely many other Creality printers, mirroring the ones that come standard with the machine. These clips are clearly designed for wire management, but unfortunately, they...

Remixed the clip from kbrouder to hold in the rails of the Ender 5 Plus a little better. 

I noticed that the original wire clip design was prone to popping out of the extrusions whenever someone merely touched them by accident. To address this issue, I modified the rounded ends of the clip that fits into the 2020 extrusions and gave them...

Wire strain relief on an Ender 3 V2 and Ender 5 Plus. Will work with other Ender machines. ... Best used with the Duke Doks V6 BMG mount: https://www.thingiverse.com/thing:4808299 Print with supports everywhere.

Ready to keep your ender 5 wiring and Bowden tube fixed? I've designed the Bowden tube and wiring wide just to helps you. Enjoy! ------------------------------ Preparats per mantenir els cables i el tub Bowden de la Ender 5 fixats? He dissenyat...

Wire organizer Wires on my Ender 5 were too short to secure against the frame so I created a set of interlocking panels. You need 2 top panels, 1 corner panel and 1 Ender port panel with t-nuts and 5mm crews. Also added a spool holder riser to fit...

... of the clip. The original clips kept popping out or falling off the extrusions with ease, so I gave them a makeover by remixing the Ender 5 Plus Wire Clip design. ...This new version fits more securely and stays put even when accidentally bumped.

This is a tweaked version of a Creality Ender 5, keeping the bowden tube and wiring harness elevated above all other components at both extremes of motion. The original wiring harness remains functional as-is, but I found it essential to install a...

This bed wire strain relief device mounts directly to the 2020 extrusion that forms the Ender 5 Plus's bed support, securing itself with M5 bolts and 2020 T-nuts without needing to disassemble the bed or any other components.

This model serves as a dependable wire supporter for the Ender 5 Plus bed, offering a sense of security. ... To assemble this supporter, you'll need to gather the following materials: - Two M3 x 16 bolts and nuts - Two cable ties

This is a basic mount that attaches above the X-axis motor, allowing you to secure your hot end/BLTouch wires and/or filament tube so they don't rub against the frame's side. The design focuses on M4 hardware compatibility. Since I have dampers on...

I did not like all the wires hanging around so I made this cover/support. Three clips snap on the frame and 3 screws are used to attach the housing to the clips. ...A cover snaps onto the housing.

Somehow my ziptied cables leading to the hot end managed to get jammed in the Ender 5's narrow crevice between the rail and the stepper. To prevent this from happening again, I designed a print specifically for this purpose. This issue only arises...

To achieve this, I needed a longer M3 screw and two cable ties for securing the Bowden tube and wire. Additionally, another screw and speed nut were required for the stepper motor side bracket. Two wire ties are necessary to keep the cable in place...

I cut part of the system down to just provide the wire strain mount. ...The whole system is awesome, but I needed this mount for a quick fix, which is also awesome!

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

Look how close that X-axis Stepper Motor wire comes to the rollers. ... Move that wire away from the rollers with this!

No supports, adjustable head angle, two M3x20 Feel free to support me with DOGE ;) DSmeW6UgGQEGP4gbfWfYAeP6aX3U1yhGju

Cable tie bracket that attaches to a 2020 rail with screws and hammer head nuts Requires: 2x M4 screw 2x M4 hammer head nut 2x 2.5mm wide zip tie

I wanted to create a way to manage the hotend cables that was easily attached to the carrier. The cables are held in place by small zip ties. This attaches securely to the spacers on the hotend carrier and does not appear to cause any issues while...

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

neatly wire route and hide the wires allowing for a very neat appearance and smooth flow wires. ...this design is pretty universal as it can mount to the side of any v rail. I simply designed it around the ender 5.

I've been using the SpeedDrive mount as modified by @paydayxray for quite a while now, but haven't been thrilled about cable-tying the wire loom to the extruder spring or release lever. So I added a sturdy cable support. It looks a bit fragile at...

... - on the inside to pevent the wires / tubes from getting stuck in front of the switch, and on the outside to give them a smooth "off ramp" from the switch. This is a remix of: [Ender 5 limit switch cover](https://www.thingiverse.com/thing:4086566)