ender 5 upgrades 3d models

Set of covers to tidy up the main wiring harness for the Ender 5. These have provision for specific cable exits for the Hot End and X, Y and X axis motor cables etc. Also provision for allen key access for the attaching 3mm tee bolts for ease of...

Ender 5 Crossbar Leider noch nicht getestet Unfortunately not yet tested Print Settings Supports: Yes Resolution: 0.2 Infill: 15% Filament: - PLA Notes: I used red fillament because I don`t have black filament at this moment. ...Will paint it in...

After experimenting with multiple designs, I stumbled upon Mistral-E Cooling Duct (https://www.thingiverse.com/thing:3255518), which turned out to be a game-changer on my Ender 5.\r\n\r\nAlthough it performed flawlessly, I still saw room for...

I modified the original spool holder to fit perfectly onto the existing Ender 5 holder without any modifications. To secure it in place, I added a slight lip on each shim that levels out the spool holder, preventing the updated holder from sliding...

A Simple Guide to Installing the Bowden Tube on an Ender 5: Ensuring Smooth Operation and Optimal Positioning. The tube easily glides through while being expertly kept in position by this ingenious guide. Strategically positioned atop the stepper...

... I designed this because I completely removed the electronics box from my Ender 5 (all of the PCBs are just sitting on standoffs now), but I didn't want the power receptacle and switch just casually flopping around with 120VAC going through them.

I designed a removable plate for the Ender 5's exposed power supply area, as the open design didn't appeal to me. To create this solution, I crafted a modular piece that can be easily taken out and put back in place. Although it needs to be glued...

I've had my Ender 5 control box flailing about in the wind while constantly fiddling with its components, so I designed these to provide a convenient way of securing it without relying on the original screws' hassle.\r\n\r\nThis design requires only...

I need to replace my spool holder because some filament I had wouldn't fit on the original Ender 5 Holder due to its lip at the end. So I measured the original including the slot for the tightening nut and printed it out without the lip. Yes, I could...

This was created to counterbalance the belt on my Ender 5. I acquired pulleys from Amazon, which are wider than anticipated, so that's what this design addresses. It can also print without support, simply rotate 90 degrees so it rests flat on its...

I made these so I could use a larger z-axis stepper motor to fix the falling bed on my Ender 5.No extra hardware is required. ...Just remove the old feet with the hex key that comes with the printer and use the same bolt to attach the extended feet.</p>

Ender5 Cover Display Upgrade. ...To implement this modification, acquire an extended IDC cable.

Suit printing from SD card via an MKS TFT touchscreen.All covered in detail here: https://youtu.be/kTm-5Vo_ekkUPDATE: I have converted my Ender 5 to run Klipper with the CB1 and Manta M4P mainboard. STL added for this combo.Print SettingsPrinter...

I liked the idea of ​​using drag chains that I saw here on thingiverse and so I decided to remix the GeekZa project: https://www.thingiverse.com/thing:4562811 editing the "90 Deg Link" (added also a right version _R) and the "Ender 5 - Hot End Cable...

The bed no longer wobbles and we are back to full steam printing at 60+mm/sec like the Ender 5 cube design was intended for! ...I realize that not everyone would like to glue things to their printer and may want a bolt-on version, so I will be...

I have many tools at my disposal, but there was no ideal location on the Ender-5 to mount one of the numerous existing toolbars available on Thingiverse. Once I found a suitable possibility, an idea struck me and some work ensued: Constructing a...

To get the electronics outside of the enclosure, I had to make these changes to the Ender 5. **Note that these changes require flashing your firmware.** First is a support brace for the bed wiring with two points for zip ties. You'll need an M4...

Since there wasn't a BLTouch mount for the Ender-5, I remixed one for the CR-10 using Tinkercad. The model's quality isn't perfect, but it gets the job done just fine. All you need to do is add one washer per BLTouch screw and you're good to go. I'm...

Ender 5 is an amazing printer able to deliver very high quality but it needs some tuning. One of the things I did was to replace the bowden extruder by a cheap direct mod. It uses the same extruder stepper and metal extruder. Cable included was short...

I have a tool box that perfectly fits on my Ender 5 Pro printer, taking into account its maximum build volume to prevent the bed from hitting the top of the box. The inside measurements of the toolbox are approximately 100x220x35 mm. It's also...

I'm having issues with my Ender 5, as it keeps hitting the carriages against the far X rail when I try to set the bed size to 235 x 235 in Marlin. When I investigated further, I discovered that the Y carriage was roughly 4mm short of the silver...

Designing a glass enclosure using the frame on an Ender 5, I'm envisioning a 30" x 36" x .092" hardware store glass that will be expertly cut at every Home Depot and Lowes location. The design features main supports at each corner, along with strips...

This is a cover I made to clean up the cables on my Ender 5 Pro. Its made in 2 parts, the outer side (mount) which bolts to the extrusion using 4x M4 bolts and captive extrusion nuts. And an inner side (cover) that then slides over and bolts onto the...

The Ender 5 is a great printer, but the bed support could have been better designed as it is hanging down in the front. Didn't find a support that I liked, so I made one myself. The bolds and nuts are M6, but probably will also fit 1/4". I used self...

This case fits perfectly with the Ender 5 and is tailored specifically for use with an SKR V1.3 or MKS Gen L mainboard, making it ideal for my particular project of adding a heated build enclosure. To prevent hot air from accumulating inside, this...

My ender 5 kept hitting the carriages against the far x rail when I tried to set the bed size to 235 x 235 in Marlin. I found that the Y carriage was about 4mm short of the silver corner brackets on the far side when it hit the Y endstop. When I...

I struggled to find good Ender 5 BLTouch Mount. So i took the best one I found and made some modifications to it to make it stiffer and more secure. You use the two shroud screws and the top left wheel screw to hold it in place. I printed it...

This case is to suit the Ender 5 with an SKR V1.3 or MKS Gen L. It is specifically designed for my application of adding a heated build enclosure. Therefore, it draws and expels air from the underside edges of the printer to avoid the hot air inside....

Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere, just measure for the lengths required. ...

More info about clipper can be found at: https://github.com/KevinOConnor/klipper Design to convert your stock Ender 5 to COREXY with linear rails This design is in working phase, has been fully tested. Current model has Microswiss/Creality stock...