ender 5 s1 top cover 3d models

Inspired by Ender 3 full PCB cover with drawers by Doc_Martin.

This protective covering safeguards the exposed printed circuit board on the Creality Ender 5 3D printer. It securely attaches to the panel using four screws that hold the PCB in place. The design features a convenient tray at the rear and a cover...

The Ender 5 Control Box Accessory: A Custom Cable Cover Project To create a sleek and secure cable management system for your Ender 5 printer's control box, you'll need to gather a few essential components. Specifically, two sets of M3x8 screws and...

They mount to the X-stepper on the Ender-3 S1 (Remixed from DrabAlarm) and completely mask the white plastic except for the area around the power connector. There are 3 variations as I'm an indecisive person: Default: - Small cutout for the...

Nothing special, just another Ender 5 Pro control box cover with ventilation slots. Printed in PETG because it was the only green filament I had on hand. :) All edges where the screen ribbon cable routes from the enclosure are rounded to prevent...

These lightweight belt covers were fabricated specifically for the Ender 5 Y-axis belts. To assemble, two M3 20mm bolts and nuts are required, which just fit snugly in place. ...The printing process took exactly one hour and three minutes to complete...

I wanted to move my screen to an upright at the front on my ender 5, and needed a cover that would interfere with the ribbon cable, so adapted this to suit, original ribbon goes in the back. ... I have never done any editing etc so if someone can fill...

Simple visualizador del extrusor para la lineal de impresoras Ender S1 y S1 Pro.No requiere de imanes ni accesorios para su anclaje. ...traba justo con el eje del motor del extrusor.</p>

Cover for Corner Angle Brackets. Inside size: 20x20x17mm Cover for: 2020 Aluminum Corner Angle, expertly fitted in my Creality Ender 5 3D Printer, to minimize vibration. ... Also check out https://www.thingiverse.com/thing:4189649 Before: After: 3D...

... as a set of stiffeners. Cover should be as low profile as possible (because Ender 5 is slick and I wanted to keep it that way). So I've measured all the control panel heights and took it in account. ... Cover should be aesthetically acceptable.

don't use support remove original cover, mount motor with shorter m3 (6-8mm) use 2x M4x10 + t-nut use nut to attach to top of extrusion on the carriage the smal holes in the right part was just a precaution you don't need those fits together with...

I love the BLTouch but the LED is extremely annoying and messes with Spaghetti Detective, so I designed this as I did not want to change the bolts to use existing designs.Clip on BLTouch cover for the Ender 5. ...It is designed to be used with this...

... designs. ... Clip on BLTouch cover for the Ender 5. It us designed to be used with this awesome mount: https://www.thingiverse.com/thing:4076996 by JackLenders. ... No bolts or other fixings required, it is an interference fit and just slides on.

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...

I wanted to add some LED lights to my Ender 3 S1 Pro's hotend, but I wasn't sure where to attach the switch. So, I came up with a solution by designing a cover that can replace the original X-Axis limit switch cover. This new cover has enough space...

Made this V slot cover for the ender 5, this part does not SNAP in, it is a loose fit . It is only for the slots at the bottom of the printer (like in the photos), they are there to keep things out of there. Keep in mind you have to cut them to size...

Overall, our new LCD cover for the Ender-5 Plus is an essential accessory for anyone looking to get the most out of their 3D printing experience. With its rugged construction, ease of installation, and noise-reducing design, it's the perfect...

My remix of the Ender 5 contol panel back cover I liked the design, but after a print I thought it felt a bit unnecessary bulky, so I took measurements of the printed part and made a new one from scratch and made it a bit thinner and also with vents....

When you access the power supply of your Ender 5, you need to unscrew four bolts from the top. These bolts are hidden under the large sticker. Completely removing the sticker is difficult because of all of the residu the sticker leaves behind. ...

I'm designing my Ender 5 Pro enclosure based on Teaching Tech's design. I was unhappy with just placing the lid on top, though. Putting hinges at the back is tough because of the Y-axis motor mount in the way. This thing is an offset hinge that lets...

I created this Ender 'X' back cover and Pi case so extra cables can be tucked in and hidden from the front view. ... Materials used standoff screws (be sure to install standoffs before screwing into the case.)

I designed a custom LCD case and cover for my Ender 5 printer that completely encases the device, including the back panel. The enclosure features a precisely placed hole to display print time and completion percentage. A hinge allows easy access to...

I wanted a LCD case and cover for my ender 5 so I made one that goes around the whole thing, back included. It has a hole for the print time and percent complete, hinged to open the lid, and lid stop so it does not open too far, all outside edges are...

This LCD cover has slots for 5 micro SD cards, 3 USB slots and 1 micro SD adapter which comes with the printer. ... This cover enables me to have these slots close by and easy to access.

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

5 inch Touchscreen and Raspberry Pi Case for mounting to Creality Ender 3 V2/S1/S1Pro (and possibly others) This replaces the stock screen on your compatible Ender series printer. This allows a 5" DSI TouchScreen and Pi 3b/4 to mount to the original...

don't use support remove original cover, mount motor with shorter m3 (6-8mm) use 2x M4x10 + t-nut use nut to attach to top of extrusion on the carriage the smal holes in the right part was just a precaution you don't need those fits together with...

Ran into a clearance issue, where the stock X-axis cover(QR code) would contact large spools, when using this top mount spool holder: https://www.thingiverse.com/thing:4368026 This is my first ever make on here so let me know if anything needs...

Protect Your Samsung Galaxy S1 with a Stylish Cover Remember, the goal is to provide a unique rewrite while maintaining the same message as the original text. ...In this case, the focus is on emphasizing that the product being described is specifically...