ender 5 s1 top cover 3d models

Mounting bracket for sensor that comes with sonic pad

I made this to mount the accelerometer in the screw holes on the heat shield part. using the included screws. Worked exactly how I intended. Only needed during test. ...then it can be removed.

These height adjustment feet (30mm to 40mm) fit between the original rubber foot and the frame in the original screw holes. Unscrew the original rubber foot from the frame.Attach it to the new “Foot” using the original M4x20 screw.Attach the new...

This is a 7.5 inch filament extension for the top of the Ender 5 pro. It is designed to sit right in front of the Y stepper motor. It is designed to use factory metal bracket and spool roller. There is two holes on top for 3mm square nuts and screws...

This is a customized EZOUT holder for users of the Ender 5 top mount spool holder with or without the Ender 5 filament guide. Since I utilized the stepper mount from the filament guide when it was installed, I needed to adjust the EZOUT to match the...

This could be used to mount filament above any of the Ender 5 series that you convert to Direct Drive and need to have the filament above the printer. This uses the stock mounting of the spool holder that comes from Creality and relocates it to the...

This is a top mount filament spool holder remix specifically for the Ender 5 Plus. The original from Les73gtx is: https://www.thingiverse.com/thing:4536704 I made this one taller and added an angle at the same time in order to move the spool...

Remixed to fit the rear 2020 bar on the Ender 5 Plus. ...Slots over the extrusion and bolts down with 2 x M4 bolts and T-nuts.

The Ender 3 S1 does has smooth metal extrusion for its frame so i could not reuse these mounts. Instead the Ender 3 S1 has 3 bolt holes, i have reused these for this model. The model is made in OnShape and is public:...

A convenient way to attach a pi-top [4] to an Ender 3 v2/S1 display mount, using screw-in studs to slot in. ... Print 2 studs from here: https://www.thingiverse.com/thing:5195246

Ender 5 pro. Remixed because I wanted a shorter bowden tube and less printing time. Also have the extruder tilted so that it can be connected in a more natural way to the filament sensor. Use M4 bolts after tapping the holes first. ... ...

Rev 1: I've added a remix of the "ENDER 5 Plus Harness Strain Relief". I wanted it to clamp on better and I increased the wall size of the wire bundle holder over the hot end. Because my version require screws to hold it together, the X Micro Switch...

I based this design off the top, side, Ender 5 extruder mount from Thingiverse (https://www.thingiverse.com/thing:3595328). I only used the bottom part to attach it to my doubled 2020 frame. While that design is pretty cool, it's mounted essentially...

Since switching to a direct drive system, I found myself needing to reconfigure the extruder holder after lowering the top spool holder. ...The next step involved recalibrating the filament sensor for optimal alignment.

- Ender5FilamentHolder-Normal = is the original part just made to fit m4 x 50mm screws - Ender5FilamentHolder-Robust = made to fit m4 x 50mm screws but also made more robust at the top I printed the robust versjon flat, with support (as shown in the...

A friend helped me remix it so that the slots on top should fit an m5 nut quite nicely and the original holes are expanded fitting the head of an m5 philips head screw such that a 20-25mm screw can be used. Might be a bit tight to reach with a...

Ender 3 S1 Drawer Insert, Nozzle for MK8 Holes

Bought a Sunlu Filadryer S1 and wanted a guidance for a bowden tube in the top hole so made this design and printed it in TPU. ...Also made a fitting plug if the guide is not in use.

So I have designed this Ender 3 S1 / Prusa MKS style bracket for the original spool holder that comes with the printer. It mounts to the top using the M3 screws and t-nuts from the handle and original spool hinge, but you will also need a single M3...

X-axis LEGO cover for ender 5

replacement Cable holder for the Ender 3 S1 Clips on the Z bracket just like the original

must have!!!! ...they fit like a glove on my ender s1 he needed a new pair of dancing shoes

made a holder for hugohuge spool holder that works with the new ender 3 s1 Z height is 46 or scaled 2540%

Because of the poor support from creality and my broken cableclip on the ender 3 S1, i redesigned the original cable clip. ... Printed with PLA+ it should work ;)

Second pipe to get two reels in your ender 3 S1 or in case you have bought the same reel support

... Version 1: Ender_5_upgrade_x_axis_motor_side_belt_pulley_cover_v1.stl 14.11.2019 Version 1: Ender_5_upgrade_x_axis_motor_side_belt_pulley_cover_v1.stl Printing Orientation: Print upside down without support. Version 1 Version 2 (Slim)

This Is a handle for the ender 3 s1 you can attach it with M3x10 bolts I printed mine in blue ABS 100% infill for Durability. ... Also used Tree Supports Print Speed 50 Print Quality 0.2

Mashup of the Control Cover and LCD Cover Found Here on My Favorite Online Community Platform

LCD cover Creality Ender 5 pro custom m2 screw Work in Progress

Display Cover for Ender 5 Plus with magnets magnets used: 6x3mm