ender 5 pro vs ender 5 plus 3d models

... you will need a few M3 screws and corresponding M3 inserts. For more detailed information about the Ender 5 Plus PrinterMods MDD mount, visit https://www.reddit.com/r/ender5plus/comments/ettlrw/ender_5_plus_printermods_mdd_a_better_bmg_mount/.

... holder, which can be found on Thingiverse at https://www.thingiverse.com/thing:4345493. This corner bracket is a remix of the brilliant relocation bracket for the Ender 5 Plus, available on Thingiverse at https://www.thingiverse.com/thing:3991856.

You can attach it directly to the Ender 5 Plus filament sensor so it is in fixed position and also it looks good! ...Make sure your filament string has enough of space from the spool and it is free from tension so it will never strongly touch to the...

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

Can be used for Creality Ender-5, Ender-5 Plus, Sovol SV05, and maybe other printer with similar shapes i dont know. Supports required from build platform. Mounting on the 2020 profile using T-nuts, 5 holes available, I only use 3 mounting points...

Cover for the Meanwell Ender 5 PSU to go with the complete bottom cooling case. ... No supports needed

Simple 5015 fan mount and duct for the Ender 5 Plus.  Compatible with the stock metal shroud & bl-touch mount and does not interfere with stock x-stop or belts. ... Only necessary modification is to remove one of the mounts on the 5015 blower fan...

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

I removed the little bucket for the SD card and USB drive since I use Klipper and a Raspberry Pi 4 on my Ender 5 Plus. ... Designed this because over time the original I remixed from lost its grip on the 2040 extrusion and started to slide down the...

A little support for the heatbed cable on the ender 5 plus, this support can be mounted to the printer with no dismantelment needed. ... Uses a M3 umbraco bolt, with a M3 nut, also need a small zip tie to fasten the cable.

I removed the stock cooling fan from the motherboard area of my Ender 5 Plus and replaced it with an 80mm fan. This shroud allows it to sit at the side of the box and uses the existing slots on the side. Vastly improved cooling and much less noise...

My take on the ender 5 plus liner rail. Used it before going to the Merc 1 setup.Heat Inserts are required for this to work well. It GRIPS the Y gantry well, I was able to have serious speed compared to OEM Setup.

This model serves as a dependable wire supporter for the Ender 5 Plus bed, offering a sense of security. ... To assemble this supporter, you'll need to gather the following materials: - Two M3 x 16 bolts and nuts - Two cable ties

Had issues keeping the hotend cables on the Ender 5 Plus from catching the printer, so created a tall bracket to keep the cable up. since installing this (with two zip ties), i have not had any issues. Will need supports. ... i used supports with a...

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. slightly larger clearance hole for microswiss plate mounting. ...Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution:...

Reworked the bottom to fit a bit better to my Ender 5 plus and made it a bit sturdier. Also resized the holes to fit some brass thread inserts in M3. ...All other needed parts can be loaded from the original source or the remixes.

My desing of a toolholder for ender 5(plus), it just snaps on the rails i print it in 3 walls and 20% cubic infill takes about 2 and a half hours,has slots for the stock hex keys the wrenches the spatula the sidecutters and some extra slots to hang...

Here are 2 Axes Fans Carriers for printer Ender 5 plus. They are design for Fan 92x92x25 / 220-110 Volt able on AliExpress for example. That's perfect to decrease the temperature of Axe motor specially when you print for a long time. ... You can...

Relieving tension on the hot bed cable of Ender 5 Plus requires this modification. No fasteners are required for this setup. Printing without supports is also possible using this method. ... This idea was inspired by BGDog's design, which can be found...

I wanted to attach my Ender 5 Plus to my IKEA Lack table cart. I made these, so I didn't have to drill through the printer frame and the top of the Lack table. ...I used these clips: https://www.thingiverse.com/thing:4091348

... very soft and flexible materials due to the shorter bowden tube. The only additional hardware needed for this modification is longer M4 bolts, at least 15mm long, qty 2. These brackets will only work for an Ender 5 Plus. ... Happy printing!

Ender 5 Plus motherboard fan bracket. Use 4 self-tapping screws to attach the holder. It is possible to use two cheap 12V fans connected in series and connect them directly to the motherboard at the 24V output. ...Use 8 M3x14mm screws to attach the fans...

More thorough print to cover more of the Ender 5 Plus bed for level testing. Note that the .gcode doesn't prime or skirt so the first disk may not print complete as the filament starts to come out. ... Be careful with where you have your clips for...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.</p> Category: 3D Printer...

this is a mount to attach the Mosquito hot-end to the Ender 5 plus carriage. ... it will work with my Satsana duct remix found here https://www.thingiverse.com/thing:5120862 Please let me know if you want any tweaks or changes.

A slightly modified belt tensioner body to fit on the Ender 5 Plus X axis carriage. ... It still requires the nut and thread part of https://www.thingiverse.com/thing:3601830 and this spacer to fit the stock bearings with an M5 bolt:...

Corner bracket for adding magnetic side panels to an Ender 5 Plus (2020 aluminum extrusion). Snaps tightly into extrusion no fasteners required. Not removable without damaging the print. pocket designed for 10mm x 60mm magnet. File included...

I build a custom Bowden and cable holder for my Ender 5 Plus, drawing inspiration from https://www.thingiverse.com/thing:3625215 but realizing it wouldn't work with my specific printer model. ...I redesign it entirely to create a perfect, stable fit.