ender 5 pro vs ender 5 plus 3d models

Ender 5 plus 2.3kg spool holder. Works with 0.75kg and 2.3kg spools. 50mm Diameter 105mm Width Mirror 3DS1 for dual setup. ... Works with the original hardware from the standard spool holder (one in each holder)

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

Ender 5 Plus Z-axis supports. Has slots (for flexibility) for M5 screws with a counter-bore for flush mounting. ... The bearing used is a 608, in this case a ZZ as I had them already.

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

A bracket that support a BTT TFT24 display inside the housig of a Creality Ender 5 Plus. Raplacement of Creality TFT touchscreen. ... Downside of this design can't use USB and SD-card slot

I'm implementing a Simple Patch for the Ender 5 Plus Filament Sensor. ...The Problem is that it's registering a False Empty Reading whenever the sensor gets nudged aside by the filament.

Will need some sanding and epoxy. ... Epoxy the Air Director to the Air Director Cover. The "tall" version can be used to keep the wires off the bed (Ender 5 Plus)

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

I couldn't get the original spacers to fit the bearings on my Ender 5 Plus. I broke several trying so I resized the spacer to 15.99mm. ...Now it slips on with a tight fit and stays in place.

Remixed the clip from kbrouder to hold in the rails of the Ender 5 Plus a little better. 

You need to connect the Ender 5 plus hotbed wires to the nearby linear bearing. ...Adjust the height according to where you attach the wire, whether at the top or bottom of the bearing.

Adapter bracket for an SKR 2. ... Made for Ender 5 Plus, could fit others. I used a SKR 2 but should fit 1.4, 1.3 also. ... Has wire tie down points at the bottom.

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

If you have an Ender 5 Plus with a Wham Bam bed, you can use this stl file and image to set it up in Prusa Slicer. Print instructionsNo printing required

Filament tube guide for the stock extruder setup on an Ender 5 plus. This support angles the tube at 10 degrees towards the bed. ... Hardware: 2) M3x16 screws 2) M3 t-Nuts

Here's a custom foot I designed for the Ender 5 Plus, printed with Cura Slicer. ... If you find this helpful, consider donating an amount you deem fair via PayPal to help offset my time spent on the design.

This is an Adapter for the tubing of the Polybox to connect properly with the Ender 5 Plus. ... This is A Remix of the of the Design by Doloth https://www.thingiverse.com/thing:4249749

This bed wire strain relief device mounts directly to the 2020 extrusion that forms the Ender 5 Plus's bed support, securing itself with M5 bolts and 2020 T-nuts without needing to disassemble the bed or any other components.

... great and have not had to relevel my bed in some time. If you would like the remix of kotopuz 4441669 design for the ender 5 let me know. ...it works fine, i also modified for finer adjustments, but the knobs interfere with the bed supports i have.

This is almost the same size as the stock Ender 5 Plus holder, maybe 2 mm shorter. It works on the Ender 5 Plus, and the Ender 3 v2. It should work with other models as well, but I have not tested it. You will need two 608 bearings. ...You can use...

... pins, while five millimeter C'Bore holes enable secure fastening to 20mm extrusion. A thoughtful addition is a central hole for cable tie organization. We're thrilled you like this design and encourage you to print one for your Ender 5 Plus today!

This is an Adapter that allows the installation of a BTT Octopus 1.1 (and also 1.0) and the Stock MOSFET that comes with the Printer into the case of the Ender 5 Plus. ... If you want to be able to access all of the Ports of the Octopus, you need to cut...

Created for a friend who bought an Ender 5 Plus and changed the extruder to gerared dual drive BMG on recommendation. Modeled from the ground up according to own measurements. ... Printed on my Ender 3 V2 with Phaetus DragonFly BMS and still :-( stock...

The Ender 3 Lead Screw Stabilizer is repurposed to perfectly fit the Ender 5 Plus. This stabilizer relies on a robust 608-2RS bearing for its stability. ...Version 3 boasts improved design, featuring smaller screw holes that significantly reduce the...

I had been using Satsana Ender 3 Fan Duct - BLtouch for my Ender 5 Plus as they share the same stock back plate. As most the Ender series printers do. Upgraded to the Microswiss Direct Drive and all metal hot end. ...and needed the part cooling...

The electronics changes include: TH3D Parts: * EZboard Lite: https://www.th3dstudio.com/product/ezboard-lite/ * Dual Z Stepper Motor Adapter with Cable: https://www.th3dstudio.com/product/dual-z-stepper-motor-adapter-w-cable/ * Heated Bed MOSFET:...

Simple Gcode for setting paper gap on 4 corners plus center of Ender 5 Plus HEAT BED AND NOZZLE TO PRINT TEMP BEFORE USING THIS TO SET PAPER GAP Print the squares to test your gap if you want. Follow CHEP's video on the Ender 3 to see how to use the...

Creality Ender 5 Plus View Spool Make it easier to see how much filament is left on the spool This is the second iteration This iteration is stronger... (This was 100% infill) NOTE you need a 100mm free space behind the Creality Ender 5 Plus to use...

I printed and sliced the Hylian Shield from Breath of the Wild using my Ender 5 Plus, making these files available for anyone who might find them useful. The files named *-Arranged show how I arranged the parts on my print bed. As my prints are...