ender 5 pro power supply 3d models

In my case, a buck converter isn't really necessary because the power supply already has a 12-volt output; however, I added one in so I can turn down the extremely quiet fan just a bit further. I uploaded my Fusion 360 files and STL files here for...

It's worth noting that this solution is not compatible with the thicker standard Ender 3 power supply; instead, I had to use an M5 tap to screw the new end caps into place within the aluminum extrusions. ...What struck me as peculiar was that one side...

The Power Supply (PS) must be unbolted from the Z axis frame and reattached to the lower frame with a plate. This allows the PS to vibrate on the X axis which can create/add "ringing" to your prints. This support bracket slips on top of the right...

... to 50 in Cura I believe).Be sure to only have one screw removed at a time. The fan will fall down into the power supply if both screws are removed.Mirrored alternative versions are included for some Ender 3 Pro models with a rotated hole pattern.

... in Cura I believe). Be sure to only have one screw removed at a time. The fan will fall down into the power supply if both screws are removed. Mirrored alternative versions are included for some Ender 3 Pro models with a rotated hole pattern.

My food having died, I had to buy this converter:...

This design was based off of the Ender 3 Power supply fan silencer by RohaniSousBois. https://www.thingiverse.com/thing:3328495 Notes on installing the part 1. Take off only one screw from the power supply fan and use it to screw the printed...

The main casing was modified to accommodate the larger PSU of the standard Ender 3 and the Y-axis bracket was modified to fit the 2040 extrusion as opposed to the 4040 of the Ender 3 Pro. As with the original design, you will need to use these side...

This converter allows you to utilize a conventional 120mm fan directly in your power supply unit. ...Fortunately, the original fan operates at a standard 12-volt voltage, making it a seamless replacement option.

I did the dual Z axis screw upgrade on my Ender 3 Pro, it was a Creality kit, the provided brackets did not work for me so I designed this bracket, test printed and made a few small revisions to the shared model.

Ender 3 Pro source silencer, it is quite quiet and the airflow coming in is very good. They can print it with whatever layer height they want or at whatever speed they find most convenient. ... Print with brackets, it will just put the brackets in the...

I did the dual Z axis screw upgrade on my Ender 3 Pro, it was a Creality kit, the provided brackets did not work for me so I designed this bracket, test printed and made a few small revisions to the shared model.

This is a remix of a remix of a very nice honeycomb PSU cover for the Ender 3 Pro which was adjusted to improve printability of screw holes and overhanging parts that are inside the model. ... The only support needed now is for the large overhang at...

This is a remix from the "Ender 3 Pro PSU Cover for 80mm" fans, where bigger is always better and I only had 120mm silent fans available. The cover has been adapted to have airflow channels at the top because hot air rises naturally. ... Fusion 360...

I'm designing a mount to attach the power supply to the bottom front of the case, since many of us use a rear-mounted design for electronics, necessitating a front placement for the power supply. This project is ongoing and I've just uploaded it so...

Remix: - https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) - https://www.thingiverse.com/thing:4771030 (Mesh Design) Purpose: - Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply Required - NF-A9X14 Noctua Fan...

* Remix: * https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) * https://www.thingiverse.com/thing:4771030 (Mesh Design) * Purpose: * Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply * Required * NF-A9X14 Noctua Fan...

Remix: https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) https://www.thingiverse.com/thing:4771030 (Mesh Design) Purpose: Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply Required NF-A9X14 Noctua Fan...

Please open photos at "fullscreen" (expand them) to see all details Recently I switched my Ender 3 Pro to dual Z (with belts) and I needed to move my PSU out of printer frame. I haven't found what I've needed, so I designed this extra rigid PSU mount...

The fan shroud has an approximate diameter of 60mm and should work on similar PSUs with 50mm cooling fans (the Ender 3 Pro uses a Mean Well LRS-350-24) but you may want to verify that magnets will be compatible. ... Autodesk Fusion 360 File (.f3d)...

This cover securely encases the PSU of the Ender 3, accommodating a widely used 120mm fan.

This is a custom cover designed specifically for the Ender 3 Pro, allowing users to install a quiet 60mm Noctua fan in place of the stock jet engine. The Noctua fan has a thicker profile than the original, which necessitates this modified cover. I...

So many fan covers/silencers with the Ender Logo, so I wanted to make one with the #1 Pac-12 Team! GO UTES! I hope there are some fellow Ute fans that decide to use this! ... Please be sure to post your print if you do, would love to see it!

The additional space in the new housing is used (optional) for: - LM2596s => Reduce voltage to the fan OR use power for additional LED strip - BBT Relay V1.2 => automatic off after printing - DC/DC 24V - 5V/3A USB => Powering Octopi The Cover is...

Fan Duct Power Supply for Creality Ender 5 Plus Infil 30% ABS

... This is for the Ender 5 and Ender 5 Pro users that are fed up with the crappy landy power supply and want to give it a good use! As always, working with high voltages is a potential hazard, and: the landy power supply is a potential fire hazard.

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

This adapter is used for fixing a standard Intel processor fan onto the Ender 3 / Ender 3 PRO power supply. The Intel processor fan needs to be prepared in the same way as mentioned in https://www.thingiverse.com/thing:4124586. However, in my...

I shifted the power supply on my Ender 3 Pro to prevent the mat from collapsing.

Power supply mounting solution designed specifically for the Ender 3 and Pro models, addressing the issue of the print bed coming into contact with the power supply unit.