ender 5 pro mods 3d models

Someone Resized the Ender 5 Plus Cable Chain Tray, but they did not include the front side in the downloads. ... So here is the front and back side parts files correctly sized and fit a 10x20mm cable chain such as this, https://a.co/d/9MJ8CyV I...

REQUIRES STOCK ENDER 5 HOT END - HOT END COOLING DUCT SNAP FITS TO THE RADIATOR. SEE ORIGINAL DESIGN FOR MORE DETAILS. I only modified the Part Fan shroud model but am including the other models here from MayoOo. ... I will add photos once the...

I designed this inspired by Jack Werner and his Thingiverse thing:4126891, but with one key difference - it stays in the front left of my Ender 5 Printer. Update 06/11/2020: I added a version with handles. The tool box itself remains the same; only...

This filament runout sensor mount is for a super cheap sensor I bought from Amazon: https://www.amazon.com/gp/product/B07N2GQHQT Remixed from this cable clip: https://www.thingiverse.com/thing:2731180 Print Settings Printer Brand: Creality Printer: ...

... either. One small ziptie and 4 M3 30mm bolts and I was good to go! Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Eryone PLA Galaxy Glitter Purple Category: 3D Printer Parts

The print layers provide a small degree of added grip I opted to not use any infill so that it allows some flexibility to make the process of fitting the cover easier. When fitting the cover onto the switch; make sure to guide the switch cable into...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

Printer: Ender 5proRafts: NoSupports: NoResolution: 0.3 mmInfill: 20 %[CZ] Vylepšení které vám umožní používat vaší tiskárnu ke psaní a malování.         K sestavení potřebujete dvě gumičky a propisku nebo fix[EN] Enhancement that allow you to use...

... from build plate to support the recesses for the wheel screw heads.  There is a small sacrificial support built in for the slot for the crtouch mount.MAy ork with Ender 3s, but I do not have one to test. OpenSCAD source included. 

Printer: Ender 5proRafts: NoSupports: NoResolution: 0.3 mmInfill: 20 %[CZ] Vylepšení které vám umožní používat vaší tiskárnu ke psaní a malování.         K sestavení potřebujete dvě gumičky a propisku nebo fix[EN] Enhancement...

Remix of this to fit a Pi 5's slightly different IO. My modelling skills are weak, tolerances could be better, etc etc. ...But it works.

This LCD cover has slots for 5 micro SD cards, 3 USB slots and 1 micro SD adapter which comes with the printer. ... This cover enables me to have these slots close by and easy to access.

... La deuxième étape imprime 5 cubes XYZ de 10mm de côté, aux 4 coins du plateau et au centre. La 3e et dernière étape consiste à mesurer les dimensions des cubes au pied à coulisse. Ce fichier STL peut être amené à évoluer si besoin. ... -3x0c3t-

La deuxième étape imprime 5 cubes XYZ de 10mm de côté, aux 4 coins du plateau et au centre. La 3e et dernière étape consiste à mesurer les dimensions des cubes au pied à coulisse. Ce fichier STL peut être amené à évoluer si besoin. ... -3x0c3t-

This is a support for a 5" touchscreen for Raspberry Pi so the printer can be fully used directly via Octoprint without opening the server on a browser. The design has been done with Freenove FNK0078 touchscreen in mind, so take it into...

... to get familiar with the latest versions of Blender and Cura on Windows and Linux platforms. To fix, two M4 bolts are required, 1.5 to 2cm long, with wide diameter washers to spread the pressure on the top of the clamp section of the support.

Here's the Chain I bought: https://www.amazon.de/gp/product/B07WJ4CPF5/ref=ox_sc_act_title_5?smid=A14H1W0K6TWKJJ&th=1 Here's the Direct-Extruder-Kit I bought: https://www.amazon.de/gp/product/B098BGFPH8/ref=ox_sc_act_title_6?smid=A14H1W0K6TWKJJ&th=1...

... nuts and washers can be found on Amazon in Alloy Steel Socket Screws Black. Hex Nuts M3-0.5 Threads Made of Stainless Steel are also available on Amazon. ...Finally, cable zip ties can be purchased from Amazon in Cable Nylon Locking Pieces Black.

5. Repeat this process for the remaining three corners. 6. Get four safety pins. 7. Cut off the sharp point of each pin. 8. Trim after the curved section. 9. Insert the pin into its corresponding hole. 10. Level the bed. Keep in mind that you may...

A simple cover for Ender 5 printers that simply rests on top of the LCD. Not hinged, nor snapped-in, as I thought those designs were too bulky and dorky. The more infill you choose to use, the more light it will block. ...Optionally, you can paint it...

Fits confirmed by users (without guarantee): Ender 3 Ender 3 Pro Ender 3 V2 Ender 3 S1 Ender 3 S1 Pro Ender 3 Max Neo Ender 5 Creality CR-10 Voxelab Aquila v2 Update V2: As suggested in the comments by...

This is a simple attachment to attach a 555 motor to the x carriage of an ender 3 or an ender 3 pro or CR 10 or ender 5. I made this to try drilling pcbs with my 3d printer. I first used the 775 motor but then I realized that a less heavy 555 motor...

The back of the display's IDC socket (i.e: not allowing for the IDC cable) is only 20mm inside the frame.Extra parts required:Two M5*8 bolts (slightly longer or shorter probably OK, too)Two M5 T-NutsYou'll need to assemble it in this order:M5 bolts...

I've compiled a list of my top picks for Essential Ender 3 Mods. In my opinion, they all perform exceptionally well and are incredibly useful. DISCLAIMER: I didn't create these mods; I simply brought them together in one project. I wish you happy...

Added a second Z-Axis: Some mods are dependent on: [Ender 3 all in one rear mount kit by TeachingTech](https://www.thingiverse.com/thing:3688967) [Cable Chain by johnniewiskey](https://www.thingiverse.com/thing:2920060) (included as an FreeCad...

A remix of McGybeer Ender 5 Cooling duct (https://www.thingiverse.com/thing:3855884). I've used MeshMixer to offset the duct so it's nozzle centered. Also chopped few millimeters of height so it won't collide with the print. ... I also printed it...

(See pichure #3) ***PART #10*** https://www.thingiverse.com/thing:2917932 Filament guide that makes the bend less bendy ***PART #11*** https://www.thingiverse.com/thing:3019402 Cover for the sceen PCB, looks clean and less scary to touch the backside...

I made this print to mount a bltouch on my Ender 5+ after accidentally destroying the original bracket. Two M3 screw inserts are required for this print (I use M3 * 4 * 5). Adding a couple washers are also useful. I recommend printing this in PLA...

Two Threes Sapphire Pro Mods Kit =========================== The following parts are available: 5010_Volcano_Fan - It's a shroud for a 5010 blower to be used with a volcano hotend, installed on the original coldend. It has a sensor mount for an NPN...

The only parts you'll need are 5 3 x 20mm bolts and self locking nuts, 2 4 x 25 mm bolts and nuts, and a 5 mm nut. I printed in eSun PLA+ 0.6 nozzle 100% infill the two linear rail supports, Spectrum petg the hot end adapter. I've added a little...