ender 5 pro mods 3d models

English: Ender printers in all variants (5, 5 Pro, 5 Plus) come with the spool holder on the right side. My printers were converted from Bowdeen to Direct and still had the spool on the side generating a lot of vibration. So I designed a part to put...

I ran into a problem with my Ender 5 Pro on prints that used the full area of the bed: the Bowden tube and nozzle power cable would get caught on the y-axis motor head, impeding motion of the y-axis and making a heck of a racket. This retaining clip...

This is a straightforward cable and Bowden tube guide I designed for my Ender 5 Pro. To avoid cluttering up my build area, I chose to route cables outside the frame wherever feasible since I'm building an enclosure around the frame. The hotend and...

This adapter was specifically designed to seamlessly connect my Palette Pro to the Ender 5 Plus. The installation process is straightforward and hassle-free, yielding a quick print that doesn't necessitate any supports. To secure it in place, simply...

This is 'yet another runout sensor' version for the ender-5 (pro). I made this so that it could be aligned straight under the extruder in a straight line. I used a spare omron 5gl2 switch, easily available on aliexpress or local store. To make it...

I upgraded my Ender 5 Pro to direct drive and was in need of a filament guide for the top-rear-left mounted spool. The new guide is 20mm wide, secured with M3's and T-Nuts. It's set at 45 degrees to avoid any sharp bends when the filament is centered...

I searched and tried a lot of brackets to fit my Ender 5 Pro but could not find any that fitted perfectly (Ender 3 brackets do not have the hole for de v-belt neither for the hole x-axis screw in the corner). There is already a 2,5mm spacer on the...

I assume the hot end design is the same for the Ender 5 and Ender 5 Plus, but have included the actual design file in two formats if you need to adjust it for your machine. This mount was designed for this gauge:...

This is a clip that can be modified for multple puproses to attach things to the Ender 5 Pro structure bars. (It should fit any printer with 20mm wide structure bars that have center channels which are approx 6mm wide) The clips do go on quite...

The Platsa spool holder by dermatin ( https://www.thingiverse.com/thing:3417593 ) unfortunately wouldn't work in this case as the Ender 5 Pro control panel + frame would be interfering. I therefore decided to hack one up (I'm new to Tinkercad) using...

This is a remix of Ender 3 Pro Tool Holder - A Remix by calaverajoe **PRINT UPSIDE DOWN** Tip of cutter hook touching plate!!! Remixception, A remix of a remix, I moved the cutter holder to work on the CR10V3 and the E5 Pro! A nice tool holder...

I added an arm and made it mountable to the frame of my Ender-5 Pro with a remix of the filament runout sensor mount from @auroratechchannel. I ended up ordering a camera for my Raspberry Pi because the SimpliSafe camera is to big. The front frame...

Very sturdy and securely mounted offering to sure up the build table on the single Z Axis Ender 5 Pro while I wait for my Dual Z Axis upgrade kit. .189" thick I-Beam type design with I-Beam flange supported .250" thick clamping collar section. ...

For Ender 5 (Pro) Edit: 21/8/2021 Changed the name plates by having them stand out, instead of being recessed. I am planning to print in white, then use "Pause at Layer" option in Cura to change the filament to black or grey and finish printing the...

... :) Print Settings Printer brand: Creality Printer: Ender 5 pro Supports: Yes only on the FilHolder_80mm change the over hang angle so the supports are only where the roller sits. ... Infill: 40% Notes: Print these standing upwards/vertical.

I couldn't find a BL Touch bracket for my Ender 5 Pro that would print properly and modifying existing brackets revealed some weaknesses and showed the Y axis belt crimp would contact the probe. I ran up a new setup based loosely on the bracket I...

For Ender 5 (Pro) Edit: 21/8/2021 Changed the name plates by having them stand out, instead of being recessed. I am planning to print in white, then use "Pause at Layer" option in Cura to change the filament to black or grey and finish printing the...

I noticed that the bowden tube is not well supported on a stock Creality Ender 5 Pro so I created this simple clip/holder to give it a bit of extra support. No screws needed, it just slides over the tube and sits on top of the hot end support...

---- When I ordered my Ender 5 Pro, it came in with a bent Y axis belt bracket. Upon doing research, I found that this is a common problem, unfortunately. I was told to bend the metal bracket back straight, which I did, but it wasn't as good as...

This is it, no more Bowden related issues on the Ender 5 Pro!Such a simple strain relief and yet so important, it removes the circular oscillation that ultimately damages the PC4-M6 coupling on the Ender 5 / Pro resulting in disastrous prints.WHY...

This is it, no more Bowden related issues on the Ender 5 Pro!Such a simple strain relief and yet so important, it removes the circular oscillation that ultimately damages the PC4-M6 coupling on the Ender 5 / Pro resulting in disastrous prints.WHY...

Fits inside my ender 5 pro without reducing print area etc. Made for standard 20x20 alu profiles so should fit any profile of that size but dont know if they would be usefull or not. Filled mine up with dried sand box sand, as its quite wet I...

After upgrade my Ender 5 pro with CrTouch + direct drive, my top mount extruder was hitting spool and sometimes just block the head when it comes home I also designed another spool holder a bit taller and backward from the head for those who have a...

Slot for replace on Ender SD Reader

Camera Holder for Ender 5 Plus I used a D-Link Network Camera DCS‑6500LH It can be rotated arround and up and down from external with an app. Yo do not have to be at home. You need 4x M5 Screw with nuts and 1x M6 to mount the camera itself on the...

This custom adaptation combines elements from two distinct variants of the Ender 5 bed strain relief design. The result is a curved configuration that effectively clears the PLA spool holder when installed in an inline setup. ...For reliable attachment,...

I use this cable holder for direct drive on Ender 5. Uses the Ender 3 X-Axis Cable Holder by ToddAustin's top piece. Haven't tested this version. I had to cut a 45 degree angle on the left side to get it to actually fit and clip in, was too wide...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

... for heavy and expensive devices. Use an M4 x 25mm (or longer) screw and nut to mount it to the cornerpiece of your Ender 5 rack. For your camera, simply add the right screw (e.g., check this one: https://www.thingiverse.com/thing:595837). ...

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...