ender 5 pro fan duct 3d models

... the back and secure the ABL mount . ABL mount - inductive 18mm probe, i´m using [Autolev ABL](https://www.substancia3d.com) ABL offset: X 51 Y 13.65 Use the remaining stl´s from: [NEbie Voron Fan Duct](https://www.thingiverse.com/thing:4916389)

... - added the ability to screw from the back and secure the ABL mount . ABL mount - inductive 18mm probe, i´m using Autolev ABL ABL offset: X 51 Y 13.65 Use the remaining stl´s from: NEbie Voron Fan Duct (https://www.thingiverse.com/thing:4916389)

Here is a fan duct with dual part cooling for the Ender 3 (Pro). For the assembly you need: - 1x 3510 fan - 2x 3010 blower fans - 2x M3x6 screws - 1x M3x12 screw Assembly: First insert all fans into their places (M2 screws for the blower fans are...

Here is a fan duct with dual part cooling for the Ender 3 (Pro). For the assembly you need: - 1x 3510 fan - 2x 3010 blower fans - 2x M3x6 screws - 1x M3x12 screw Assembly: First insert all fans into their places (M2 screws for the blower fans are...

Thank you!Paypal.me link: https://paypal.me/adarkstudioThank you page: https://pastebin.com/raw/gTt8iE5aCheersNio (ADKS)Previously…In an attempt to quiet my Ender 3 Pro, I designed this hotend fan duct to use 4010 or 4020 silent fans only. ...The other...

I had big prints with some stringing, and the front fan of the ender 3 kept pulling in air just above the printed parts and pulled the pla strings onto the hot end. This duct changes that airflow so that air is pulled from above. The Parts is just...

I increased the wall thickness of the part that goes into the fan shroud on a few key points. I print with a 0.6mm nozzle and some spots were coming up single walled. I also extended this so that it hooks into the other side of the hotend cage. ...

simple bolt-in replacement for the stock cooling fan duct. ...This new duct redirects the fan air closer to the nozzle and blows onto the part more accurately.

So i modded the original Ender 3 Pro Mainboard Metal Cover to fit two fans and directly blow onto the stepper heat sinks. Of course also used a step-down converter to run the 12V fans at 8V, so that they are very quiet now. ...Additionally used TPU...

To be able to test out the design from NEbie and mount on an Ender 3 / PRO, first i had to make some changes and new parts.Changes:. extruder clamp - original was rubbing the X axis profile<br>. left mount - added the ability to screw from the back...

Satsana_5015 Duct Fan Remix V1 - Logos inserted - 5015 duct fan cable guidance inserted - Right exterior wall reinforced and holes for BL Touch removed Version V2 - Cable guidance replaced through hole - Cable tie hole relocated to the outside

... Pro. ...To do this I had to design a new fan duct. I hope this can save others some time.You'll need to add two M3 nuts to the screws which hold the hot end in place as the Ender3 hot end is thinner than the standard CR10 hot end. They act as spacers.

... assemble. Get the perfect setting for your machine. Print at higher speeds. The download comes with mounting instructions and screws to be used. https://youtube.com/shorts/WP7gH3xE9H4 New V5 fan bracket and new V5 pipe shaped duct, better flow.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

Instead of adding more fans on the printer head where it adds weight and make it sometimes ugly huge to be effective, this puts the blower on the side of the X axis beam and so it isn't putting any more weight on bad places while still adding much...

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket. Category: 3D Printer Parts

The FAN duct is as close to the original as possible, but has a little more distance to the hotbed. The design has no corners, so the air can blow straight from the blower-5015 to the nozzle. The air from the blower is taken from the hotbed as in...

Currently my latest version for Ender 3/Pro with 4 wheel cart (from Aliexpress) for Direct Drive and BLTouch. ...I lowered the height of the air tunnel a bit for better visibility of the hot end.

Fan Duct Power Supply for Creality Ender 5 Plus Infil 30% ABS

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where needed...

Hello Have a nice day

This is a remix of a remix of the fan duct, that will fit better (not perfect) if you have a micro swiss hot end installed. I'm not an expert (first remix) i took the existing model, i've put it in fusion 360, cut it in half and added 3mm on the Z...

I remixed the settings to match my Ender 3 Pro purchased in December of 2019. You may need to check the original files if your printer requires a second set of tabs. No built-in supports are available, so external support is necessary. I use 10%...

Basically, I extended the fan outputs 10mm so it reaches the nozzle of a regular volcano hotend. WARNING: This model is untested, so I can't guarantee itl fit. I'm going to print it at a later date and edit this as follows. This model is split...

... For the BLTouch, the XY-Offsets should be as follows: define NOZZLE_TO_PROBE_OFFSET {-37, -16} There is now a new and improved version of the MicroSwiss DirectDrive Fan Duct for the Ender 5 available here: https://www.thingiverse.com/thing:4856649

This is a reworked version of the MicroSwiss DirectDrive Fan Duct for the Creality Ender 5. It's based on this remix i did: https://www.thingiverse.com/thing:4832331 and it uses my new combined BLTouch adapter:...

Pro Fan Duct CR10s Upgrade\r\n\r\nJune 5, 2019 Upload

Creality CR-5 Pro High Temperature original fan duct was crooked enough to hit print surface, existing models found in Thingiverse did not open correctly or were erroneous. ... So made a new simple design.

For each fan 2-4x M3x8 screws should do. . For collision avoidance checking I used a step model of the Creality Ender 5 pro from the user "barnabyQ" at https://www.grabcad.com/library/creality-ender-5-pro-1. . The XY-Offsets are as follows: -BLTouch:...