ender 5 pro enclosure 3d models

This mount is for the EZABL Pro 18mm. My offsets for this mount are X-51 & Y-12. The offsets for the original mount were X-57 & Y-22. This mount will feel a little flimsy but will work fine to hold the very light EZABL. ...As a reference I have my fang...

I make a remix for use direct extruder Orbiter 1.5.

This is an innovative Electronics front enclosure designed specifically for Ender 3/Ender 3 Pro, perfectly tailored to fit:\r\n\r\nBigtreetech E3 Mini\r\nRasperry Pi 2/3\r\n4x LM2596\r\n1x Noctua Fan 40x40\r\nThe design has been cleverly divided into...

... set them at same position, install X 2020 beam, and fine adjust, the Y- distance to the Frame, then tighten the coupler. Use hex pattern or triangles infill. Wall line count (perimeter) 5 Concentric bottom and top pattern looks better ;-)

... Plates, set them at same position, install X 2020 beam, and fine adjust, the Y- distance to the Frame, then tighten the coupler. Use hex pattern or triangles infill. Wall line count (perimeter) 5 Concentric bottom and top pattern looks better ;-)

I made a custom mount so I could shorten my Bowden tube, allowing me to reduce retraction during prints to 5-6mm with PETG and minimize stringing. To replicate this mod, you'll need a stepper motor extension cable and a PTFE Bowden tube kit with M6...

The Duet 3 Mini 5+WiFi is the same size as the older Duet 2 with a few changes to the layout so the original case design would not work. I like their design so it was modified to fit the new board. The printer has a smart filament sensor so a slot...

————————————————— Raspberry Pi W/5' TFT LCD holder for the left side is in progress - I'll remove "in progress" status when it's finished printing and tested. PRINT IN CURRENT ORIENTATION I use a 0.6 nozzle. ... Layer Height: 0.36 Initial Layer...

This is an enclosure I designed to house the MKS TFT28 display and mount to the left 4040 extrusion of my Ender 3 Pro. It's a snug fit when assembled together. The Clamshell closes up with four M3x8mm screws, but you may need ten-millimeter length...

Carénage avec fan duct conçue pour avoir une meilleur solidité et un meilleur refroidissement, ce dispositif correspond uniquement pour l’imprimante ender 5 plus avec le système microswiss. Le fichier contient : • Fichier STL • Fichier CTB SATURN ...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the same...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the same...

The enclosure adapts the printer's vendor-supplied filament holder provided by Creality CR-10S Pro printers. It is also believed that this same holder comes with Ender 3 printers, however, this needs to be confirmed first. To install the enclosure,...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech E3 Mini Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join the parts and...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech SKR 1.4/1.4 Turbo Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join...

Please use v042 for Raspberry Pi 2/3** This is an enclosure that I designed to go under the LCD display of the Creality Ender 3 Pro (probably will fit perfectly to Ender 3 too) that also holds a Raspberry Pi 2/3 and now 4. ~~Later on, upon request,...

This is a remix of eoyilmaz's Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure https://www.thingiverse.com/thing:4586351 This has been modified to fit the Libre Computer Board AML-S905X-CC LePotato board. At the time of this writing...

Saludos English: Ender printers in all their variants (5, 5 Pro, 5 Plus) come with the roll holder on the right side. My printers were converted from Bowdeen to Direct and I still had the coil on the side generating a lot of vibration. So I designed...

... bit to cut them. You need to hold the plex to the top of the opening when you mark the holes - it slots in, then lowers to lock in place. This does leave a 1/8" gap at the top. It holds the heat in well, though. Printed on Ender 3 pro with PETG.

Here's the External Enclosure for the Ender 3 or Ender 3 Pro that will blow your mind - you have options galore! Want to put a SKR 1.3 board inside? Go for it! Creality 1.1.4 board in it? Easy peasy! How about an MKS MOS25 mosfet or a RepRap Champion...

Oh, did I mention it's an EXTERNAL case for those of you who want to put the Ender 3 or Pro into an enclosure? Please consider providing a Tip for the Designer as I am on a very limited Social Security income. I do these designs because I have fun...

I would also like to credit Hesi_Re for a fan mount which was a part of an Ender 5 LCD enclosure design. Obviously the enclosure wouldn't fit my Ender 3 but the fan mount fit perfectly with the Pi4. The fan mount was remixed as well to allow...

Here's My Design for the Ender 3 Pro: A Comprehensive Upgrade Guide If you're planning to upgrade your controller board on the Ender 3 Pro, this design is specifically tailored for the SKR 1.3 or MKS Gen L boards. While it should also work seamlessly...

Big Extruder Knob for the Creality Ender 5 / Ender 3 Pro / CR-10 Maybe there is someone out there need a bigger extruder knob like i did, 150 micron, 25 infill, and pla will be enough

This includes a cut out for the 4040 Damper legs in the front Right corner for the Ender 3 Printer.

Source: https://www.thingiverse.com/thing:4485990 I did not test this for fit, instead copying the Pi side input locations directly into the enclosure. ...If you spot any errors, please feel free to use the included STP file to create your own revised...

I designed this parts to build an "lack Enclosure". Main facts: i used 28, M4 screws and nuts to mount the 2mm thick plexiglass to the printed parts. the plexi on the right, left and at the back are each 45cm x 49cm but there will be an 5mm...

Changed: 1) 120 MM Fan 2) Completely new Back/Top Design 3) Redesigned Interior Structure 4) Fits MKS Gen L AND a Raspberry Pi Internally 5) Space for Buck Converter for Rasp Pi 6) Uses Ender3 Pro Stock Power Supply 7) Removed top LCD and added a...