ender 5 pro cable management 3d models

Ender 5 Pro Y axis drag train tray. ...20x10 Chain

... to hide thin cables. ... In my case a WEB camera cables and OctoPrint connections on the front of the Ender 5 Pro. It is a very strong clip if using PLA+ and printed thick enough not to collapse. ... It takes about 40 minutes to print 6 clips...

This is a straightforward cable and Bowden tube guide I designed for my Ender 5 Pro. To avoid cluttering up my build area, I chose to route cables outside the frame wherever feasible since I'm building an enclosure around the frame. The hotend and...

I recently made my ender 5 pro a direct drive printer. I wanted to keep the filament on the same place so i made a bracket to connect the ptfe tube close to where the extruder used to be. Also made a simpel cableguide in it where you can fix the...

Cable chain tray remixed to fit Ender 5/Pro. Tray have been scaled to fit with 10x20 generic chain. https://www.aliexpress.com/item/1005001795469984.html I do not use the x axis tray but added it in case someone needs it. X axis tray have not...

Kabel Kabelmanagement Kabelhalter für X- Y-Kabel Ender 5 V7 ist etwas kleiner als V6 prüft was ihr hier benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier: http://jogiarea.de/ ---------------- Cable management cable...

Kabel Kabelmanagement Kabelhalter für X- Y-Kabel Ender 5 V7 ist etwas kleiner als V6 prüft was ihr hier benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier: http://jogiarea.de/ Cable management cable holder for X- Y-cable...

Someone Resized the Ender 5 Plus Cable Chain Tray, but they did not include the front side in the downloads. ... So here is the front and back side parts files correctly sized and fit a 10x20mm cable chain such as this, https://a.co/d/9MJ8CyV I used...

I use this cable holder for direct drive on Ender 5. Uses the Ender 3 X-Axis Cable Holder by ToddAustin's top piece. Haven't tested this version. I had to cut a 45 degree angle on the left side to get it to actually fit and clip in, was too wide...

I needed this part for organizing cables of my ethernet cables. I needed them to be screwed down. ...Thus, I designed it!

... to get familiar with the latest versions of Blender and Cura on Windows and Linux platforms. To fix, two M4 bolts are required, 1.5 to 2cm long, with wide diameter washers to spread the pressure on the top of the clamp section of the support.

After changing the hotend to the creality Spider i have to design an new cable guide. This is it. ...No gimmicks, no fancy design.

... Changes to the original design - Added bolt mounting holes ( M3, and with the help of a drill M4 ) - Removed the zip tie holes - Filled in unused cable hole on the side - Added bolt mounting point on the back All fits well and slides in easily,

Here's the Chain I bought: https://www.amazon.de/gp/product/B07WJ4CPF5/ref=ox_sc_act_title_5?smid=A14H1W0K6TWKJJ&th=1 Here's the Direct-Extruder-Kit I bought: https://www.amazon.de/gp/product/B098BGFPH8/ref=ox_sc_act_title_6?smid=A14H1W0K6TWKJJ&th=1...

Designed up this mounting bracket for ender 6 cable management to use in ender 6. . ... Printing: Printed in ender 6 Print time 35 minutes 100% infill Print Speed 200%

This is a simple rear cable management mount for the Ender 6. ...It requires 2 - M3x15 screws and 2 - M3 T-nuts.

Simple cable management for Sapphire Pro.Print 0.18 or 0.2 Layer HeightInfill: 30%Note: If you wat to print without supports, rotate the model by 90 degrees

I only printed one of each, thinking it would fail miserably, but to my surprise nothing was wrong. I hope these can help you too in managing cables on your printer (these clips will work with other printers that have aluminum extrusions similar to...

This enclosure is specifically designed for the Ender-3 to keep cables organized. It includes space for a 3x6cm protoboard. ...To attach it to your Ender-3, you'll need M3 screws and V-slot nuts.

I created this cable management system that routes the cables in front of the z axis pillar to avoid cable binding as the gantry moves up. The cable mount pivots in the base for flexibility while the x axis traverses. ...I included zip tie anchor points...

A major design philosophy of my Ender 3 Pro is to be as self contained as possible. I got tired of having to disconnect/detach/untangle everything in order to move the move to out of my enclosure to work on, so I have minimized this, and now, with...

This is a filament guide I remixed from a few people I was having problems getting the best of both worlds (cable management and good filament guiding). So, I did it myself and made this great filament guide. One downside is you need a connector for...

... have to place it where the Z-axis end stop already is. Extra parts. Chassis mount: M4 x 12mm + T Nut (x 4) M4 x 30mm + Nut (x 2) Hotend mount: M3 x 8mm (x 2) or the same by Ender Chain cable carrier https://www.amazon.it/gp/product/B094ZSWDWB/

The clip attaches seamlessly to the extruder's stepper motor and the t-slot bracket keeps the printhead cable out of the way as the printbed moves. ...Fasten the cable with zip ties at the marked spots for extra security.

print this in two pieces, top and bottom. ... glue together. it snaps on to the Y motor cover. This supports the extruder cables. ...

Wire organizer Wires on my Ender 5 were too short to secure against the frame so I created a set of interlocking panels. You need 2 top panels, 1 corner panel and 1 Ender port panel with t-nuts and 5mm crews. Also added a spool holder riser to fit...

I also included a cable tie mount to keep cables organized and out of the way. When installing this part, push it gently towards the rod because the space between the filament and the guard is quite narrow. Note: I replaced the original washers...

Motor side: Two cable chain adapters for johnniewhiskey's Ender 3 Cable Chain (https://www.thingiverse.com/thing:2920060) are used in my design. One adapter leads outside the enclosure to the electronics box, while the other leads inside the...

Cable cover for ender 5 pro for screen relocate and new cable Screen Relocate : https://www.thingiverse.com/thing:4600011 SD adapter : https://www.thingiverse.com/thing:4670609

These are my custom config files for the Ender 5 Plus with Marlin 2.0 Firmware on a SKR 1.3 motherboard (I have a 1.4 Turbo installed, but I haven't had time to update it yet). They are very specific to my machine, but I thought others might find...