ender 5 plus 3d models

Perfect mount for the Reolink E1 on the Creality Ender 5 Plus Fastening material: 2x cheese head screw M4 x 10mm 2x hammer nut for 6mm nut. Thread M4 Attention! ...I printed it out of PLA, if you often print ABS or ASA with a enclosure, please...

... to increase the sides to 3mm instead of 1.5. I also increased the thickness on the mount for the Ender 5 Plus because I found that the original "wiggled" too much on my printer when mounted. ... I added two additional screws to the block as well.

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

Hello all out there, Here is a big decorative cornet bracket for ender 5 plus printer (or other large printer) I don't know if its useful, but it fill the empty side of the printer. Size 200*200 mm with 50mm clearance. This thing could be used...

Namely: https://www.thingiverse.com/thing:4437226 https://www.thingiverse.com/thing:4492841 This fan duct will fit over the original BLTouch mount and the X Axis belt on the Ender 5 Plus WARNING This will push your part cooling fan right about 1cm. I...

I'm using it on my ender 5 plus inside the enclosure to monitor both temp and humidity in there. It mounts with 2 m5 screws and a couple Tnuts. Step file included for those of you that need or want to modify it. ... Be sure to use support when...

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

I wanted to mount a Voron M4 extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5 screws...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

The official Creality all-metal extruder upgrade (Pictured) sits slightly wider than the standard plastic Ender 5 Plus extruder, causing the filament exiting from the filament runout sensor to misalign with the new metal extruder. I created a...

Remix of Giuliano Moschini's fanshroud assembly for the MicroSwiss Direct Drive for the Ender 5 Plus. I trimmed it down if someone wants just a strain relief. I added channels for 2.5mm smaller zip ties. I printed this on my CR-20 Pro with a .2mm...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...