ender 5 plus 3d models

Reworked the bottom to fit a bit better to my Ender 5 plus and made it a bit sturdier. Also resized the holes to fit some brass thread inserts in M3. ...All other needed parts can be loaded from the original source or the remixes.

I wanted to attach my Ender 5 Plus to my IKEA Lack table cart. I made these, so I didn't have to drill through the printer frame and the top of the Lack table. ...I used these clips: https://www.thingiverse.com/thing:4091348

Had issues keeping the hotend cables on the Ender 5 Plus from catching the printer, so created a tall bracket to keep the cable up. since installing this (with two zip ties), i have not had any issues. Will need supports. ... i used supports with a...

This is to relocate the stock touch screen on the Ender 5 Plus.I relocated my electronics to a back plate and thus had to make a separate mount for the screen as i removed the original electronics casing.screws together with M3 screws and a single M5...

A slightly modified belt tensioner body to fit on the Ender 5 Plus X axis carriage. ... It still requires the nut and thread part of https://www.thingiverse.com/thing:3601830 and this spacer to fit the stock bearings with an M5 bolt:...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.

A little support for the heatbed cable on the ender 5 plus, this support can be mounted to the printer with no dismantelment needed. ... Uses a M3 umbraco bolt, with a M3 nut, also need a small zip tie to fasten the cable.

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

More thorough print to cover more of the Ender 5 Plus bed for level testing. Note that the .gcode doesn't prime or skirt so the first disk may not print complete as the filament starts to come out. ... Be careful with where you have your clips for...

Use the longer one for both front and back if you have an ender 5 plus. The light bar is long as I wanted as much light possible on my ender 5 plus. If you need less of a strip, just resize it in your slicer. Ender 5 plus has a huge print bed. If...

This is a remix of zarify mount https://www.thingiverse.com/thing:4087221 but made to fit an Ender 5 Plus It wont quite clear the hot end but does a good job and doesn't require and additional hardware. ... the cover is friction fit and you may need...

Simple 5015 fan mount and duct for the Ender 5 Plus.  Compatible with the stock metal shroud & bl-touch mount and does not interfere with stock x-stop or belts. ... Only necessary modification is to remove one of the mounts on the 5015 blower fan...

I build a custom Bowden and cable holder for my Ender 5 Plus, drawing inspiration from https://www.thingiverse.com/thing:3625215 but realizing it wouldn't work with my specific printer model. ...I redesign it entirely to create a perfect, stable fit.

This model serves as a dependable wire supporter for the Ender 5 Plus bed, offering a sense of security. ... To assemble this supporter, you'll need to gather the following materials: - Two M3 x 16 bolts and nuts - Two cable ties

My take on the ender 5 plus liner rail. Used it before going to the Merc 1 setup.Heat Inserts are required for this to work well. It GRIPS the Y gantry well, I was able to have serious speed compared to OEM Setup.

Here are 2 Axes Fans Carriers for printer Ender 5 plus. They are design for Fan 92x92x25 / 220-110 Volt able on AliExpress for example. That's perfect to decrease the temperature of Axe motor specially when you print for a long time. ... You can...

I removed the little bucket for the SD card and USB drive since I use Klipper and a Raspberry Pi 4 on my Ender 5 Plus. ... Designed this because over time the original I remixed from lost its grip on the 2040 extrusion and started to slide down the...

Relieving tension on the hot bed cable of Ender 5 Plus requires this modification. No fasteners are required for this setup. Printing without supports is also possible using this method. ... This idea was inspired by BGDog's design, which can be found...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.</p> Category: 3D Printer...

This a printed version the gantry plate from 3dfused that is used for their Ender 5 Corexy conversion (fits the stadard, pro, plus kits) - https://3dfused.com/product/ender-5-plus-corexy-kit/. This can also be used on the Mercury One Corexy...

Simple Gcode for setting paper gap on 4 corners plus center of Ender 5 Plus HEAT BED AND NOZZLE TO PRINT TEMP BEFORE USING THIS TO SET PAPER GAP Print the squares to test your gap if you want. Follow CHEP's video on the Ender 3 to see how to use the...

Slovak language: Upravil som môj Ender 5 plus na direct (stl: https://www.thingiverse.com/thing:4310609) a výmenu filamentu vpredu. Ptfe je schválne rozdelená aby sa ľahšie zavádzal filament a bol menší odpor pri retrakcii. Na úpravu stačia pôvodné...

I had been using Satsana Ender 3 Fan Duct - BLtouch for my Ender 5 Plus as they share the same stock back plate. As most the Ender series printers do. Upgraded to the Microswiss Direct Drive and all metal hot end. ...and needed the part cooling...

You can attach it directly to the Ender 5 Plus filament sensor so it is in fixed position and also it looks good! ...Make sure your filament string has enough of space from the spool and it is free from tension so it will never strongly touch to the...

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

Inspired by a fantastic video from Tripod in his garage, where he provides an extremely detailed walkthrough of installing Bigtreetech's SKR 1.4 into an Ender 5 Plus, based on KAY3D's Cheetah 5.0 Marlin Firmware. Since I had acquired several SKR 1.4...

Work in Progress Remix of the TeachingTech Concept: Please note that this concept differs from the original due to the specific format of the Ender 5 Plus! To build a case for the Ender 5 Plus, you will need: - 4 V-slot profiles of 495mm - 4 V-slot...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...