ender 5 plus 3d models

Here is my own design for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with Linear rail. 2 x 5015 component fans, 4010 or 4020 Hotend fan, BL Touch bracket and cable routing to the top. Put the fusion file in here with it, anyone who...

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the...

I converted my Ender 5 Plus Extruder to a Biqu H2 direct drive. I wanted a way to have the filament feed from the top instead of through a bowden tube. I created an offset mount that can hold any filament up to 5kg. I wasn't sure how the filament...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

Bretware Ender 5 PLUS Chain System, BTT Octopus Version Meanwell PSU window Cover only at this time, message me if you need a different cover. Please subscribe to our Youtube channel we need to get to 1000, thanks. Kiss wires good bye, puts the Y...

Due to the Ender 5 Plus's independent Z screws, they can easily get out of sync, making it a challenge to maintain proper alignment. Removing any part can cause the bed to fall and become misaligned. If you're like me and don't run auto-bed leveling...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

This is a complete overhaul of the ender 5 plus's gantry. After trying the Merc One core-xy mod, I found that the belts were far too long to prevent ringing, and the belt path too complex to avoid problems. Also, the stock belt arrangement really...

---------------------------------------------------- This is my design for a kinematic self levelling bed system for the Ender 5 plus. This design allows you to fully automate the levelling of your bed to a very high precision - meaning you only...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus.NotesRecommended parts have “rev4” present (except for the buttons).  Alternatve parts (refer to “Earlier Revision Options” above) have "rev2" or "rev3"...

This is a linear rail mod for the Ender 5 Plus. It encompasses the XY&amp;Z axis. I designed these parts because I was unhappy with most other mod variations of them.</p><p>Z Axis - The Z axis part were designed using the BLV MGN Cube as a starting...

This is a linear rail conversion for the Ender 5 Plus. It encompasses the XY&Z axis. I designed these parts because I was unhappy with most other mod variations of them. <b>Z Axis -</b> The Z axis parts were designed using the BLV MGN Cube as a...

Prolunga per sensore filo di crality ender 5 plus.

This is a V6 mounting with custom cooling for the Ender 5 and 5 Plus. Currently it supports 4020 fan blowers, but Im planning to add more variants in the future. Also direct drive mod for this is in progress - it will probably work with this parts...

This is a V6 mounting with custom cooling for the Ender 5 and 5 Plus. Currently it supports 4020 fan blowers, but Im planning to add more variants in the future. Also direct drive mod for this is in progress - it will probably work with this parts...

This is for mounting the E3D Hemera as bowden extruder. ... Hardware Required: Bowdapter by E3D 4 x M3x8 2 x M4 T-nuts (From Ender 5+) 2 x M4x12 (From Ender 5+) Filament sensor and screws (From Ender 5+) PTFE Tube (30mm or longer)

I replaced the ender 5 enclosure with a new one, using 1/4 inch thick Plexiglas. ...To reinforce the corners, I implemented a few modifications to improve their structural integrity.

... Thingiverse. I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

... I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

... I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

After seeing someone else's solution, my mind fixated on that issue all day until it was solved on the Ender 5+. Here's what I came up with: you can even attach another Bowden Tube fitting to it (a necessity for those using mounted rolls feeding into...

#FERMETURE DE L'IMPRIMANTE# ##Fermeture latérale:## - 6 x équerre grand v2 - 6 x équerre petit - 1 x support câble chain - 1 x X Axis Cover bracket MODIFIED (https://www.thingiverse.com/thing:4846288) ##Fermeture supérieure/couvercle:## Solution...

#FERMETURE DE L'IMPRIMANTE# ##Fermeture latérale:## - 6 x équerre grand v2 - 6 x équerre petit - 1 x support câble chain - 1 x X Axis Cover bracket MODIFIED (https://www.thingiverse.com/thing:4846288) ##Fermeture supérieure/couvercle:## Solution...

2020-08-15 Check out this link for updated files: https://www.thingiverse.com/thing:4570662 __________________________________________________________________ New light bars and supports are now designed to fit seamlessly with Ender 5 mods. These...

I needed a screen housing for my Ender 5+, when I changed the screen to a 12864 LCD. Because I have removed the electronics from the enclosure, I could not use anything that mounted to the extrusions. Therefore, I created this. Of course, you can...

These gcode files were specifically sliced for use on Ender-3 printers. This updated version extends the arm to prevent the black cable cover from making contact with any parts of the y-axis motor or rods. Additionally, it provides support for the...

That plus an SKR for the steppers, and I won't lose quite as much hearing before going back to my office in the year 2025 maybe? Printing: I meant to do the bottom and middle in ABS, but I did the top in ASA. When I printed the bottom, I used ASA,...

Français Clip pour cacher le câble USB de la caméra dans un Profilé Aluminium 20x20. Il est simple mais efficace. Il suffit de régler la longueur dans votre slicer. J'espère que cela vous servira. English Clip to hide the camera's USB cable in a...

<p>Material ASA + threaded insert M3</p><p>LCD Adapter :</p><p>Remix <a href="https://www.thingiverse.com/thing:4972042">https://www.thingiverse.com/thing:4972042</a></p><p>Board Adapter:</p><p>Remix <a...

This is a remix of https://www.thingiverse.com/thing:4670117 This wil fit with an embedded nut soldered in M5