ender 5 plus 3d models

I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the pics in the link: ...

... of the bed is necessary to ensure adequate printing height, given the adjustment to the 8mm rod brackets. Following these modifications, the risk of collisions is eliminated, allowing seamless integration with the original Ender 5 Plus firmware.

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

Hello all, Here's an ajustable webCam support for Ender 5 plus ... or for all printers that has 2020 profil All the parts can be printed without support except for part 7. All the parts are printed mostly on the side edge so that the holes are...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

Simple yet effective replacement for your Ender 5 Plus duct fan. Exhaust is directed under a small angle, now featuring rails, so airflow points directly at the nozzle tip. I hope you'll be satisfied with the results. If any issues or tips arise,...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. BLTouch mount is about 5mm to the left of the...

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. Hope you will be happy with the results. In case of any problems or tips do not...

This piece supports the wire going to the hot end on the Creality Ender 5 Plus. The V4 file is designed to connect to the printer with two M3x10 machine screws and two M3 T-nuts, while the tube connects with a zip tie or twist tie. This piece...

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

This is a Ball-Bearing Filament holder for Creality Ender 5 Plus (or possibly other models) designed to accommodate filaments weighing 1000g or less with an inner diameter of 52mm. To complete this project, you will need two sealed ball bearings...

This extend your Ender 5 Plus rubber feets by 35mm. (I need this for my own silent cooling solution, maybe I will show you later). Maybe you like this too to add more airflow to the Z stepper motors. You need 4mm brass inlays, so you can reuse the...

...My design has been put to the test on my Ender 5 Plus printer, which operates seamlessly without any hardware holding it back. To accommodate varying bed thicknesses, users can fine-tune their designs using the scale feature in the slicer software.

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

VIDEO: https://www.youtube.com/watch?v=RpIH-jXLHm8 ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:...

If your printer uses the same carriage plate that the ender 5 plus does then this should work for you too. This uses the stock BLtouch mount and you can use the stock 40mm fan but if you want the cooling fan you'll need a 5015 blower (I have not done...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. ...

Remix of Ender 3 - Filament Holder Deluxe (https://www.thingiverse.com/thing:3114139) for Ender 5 Plus (tried to upload it as remix, but Thingiverse is not able to find the original design) - I was happy with the original design that I have used on...

Decided to go another route, but if I had kept it I would've reprinted in PETG.Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.Print SettingsPrinter...

My take on the low friction spool holder designed to fit the Ender 5 Plus bracket. It ended up being too low friction and would spin on its own. ...I added some foam between the spacer and the spindle body, which resolved the issue. Required Hardware:...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish. ...

This model is designed to fit a Vizio xr6m10 tablet (5.5 x 3.5 x 0.2 inches), but you can easily update the model to work with other phones/tablets by tweaking the [Tinkercad...