ender 5 plus vs ender 5 pro 3d models

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

Namely: https://www.thingiverse.com/thing:4437226 https://www.thingiverse.com/thing:4492841 This fan duct will fit over the original BLTouch mount and the X Axis belt on the Ender 5 Plus WARNING This will push your part cooling fan right about 1cm. I...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

This spacer is specifically designed for users who have installed the BondTech BMG extruder on their Creality Ender 5 plus and still want to utilize the filament run-out sensor. *Update* I initially provided an incorrect spacer, which I promptly...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

Simple tool to install the silicon sock on stock Ender 3 and Ender 5 Plus. May fit on other machines. ...Prints in 2 pieces and is glued together.

Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Use supports. ... Enjoy !

Gehäuse für das Bigtreetech TFT70 v3 um es an den Ender 5 Plus zu verwenden. Die Bodenplatte habe ich mit 5 Magneten 1x8mm die in die Aussparungen eingeklebt werden befestigt, somit kann man sie jederzeit abnehmen. Man Kann Sie aber auch mit...

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

Bolts to the side of the bottom 2020 extrusion on the Ender 5 Plus. My printer is enclosed on the sides so the 3mm tube that comes with the dryer loops around, goes through a hole in the side and feeds into a filament guide arm which then feeds up...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. ...BLTouch mount is about 5mm to the left of the...

This is to mount a Duet 2 Wifi and paneldue in an Ender 5 plus positioned in a way to get maximum Wifi signal. ...you will need to move the mosfet to do this mod, use: https://www.thingiverse.com/thing:4888746 The screen cover and mount is found...

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

Extended version of trays to fit the Ender 5 Plus Original parts still required from: https://www.thingiverse.com/thing:4116655 Changes: X-Axis screw holes reduced for M3 screws X-Axis Right, modified to fit around endstop, so no need to change....

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

I got tired of trying to get the whole bed carriage level on my Ender 5 Plus. It tends to sag a little when the power is off, and I struggled to get it back to level every time I powered it on. This simple solution fits on top of the bed frame and...

Bracket to hold a digital indicator gauge to my Ender 5 Plus for bed leveling. Found a few brackets out there but all showed much more expensive gauges in their pics. The gauge I went with was fairly inexpensive and I wanted to ensure my bracket...

This is a top mount filament spool holder remix specifically for the Ender 5 Plus. The original from Les73gtx is: https://www.thingiverse.com/thing:4536704 I made this one taller and added an angle at the same time in order to move the spool...

I've been struggling to prevent the hotend cables on my Ender 5 Plus from getting tangled up in the printer, so I came up with a clever solution: designing a sturdy bracket that keeps the cable elevated out of harm's way. Since installing this...