ender 5 plus vs ender 3 s1 plus 3d models

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

I got tired of trying to get the whole bed carriage level on my Ender 5 Plus. It tends to sag a little when the power is off, and I struggled to get it back to level every time I powered it on. This simple solution fits on top of the bed frame and...

A custom strain relief for the Ender 5 Plus extruder, crafted with precision using PLA and optimized settings from the factory slicer. To bring this design to life, you will need: 1. An M3 x 12mm Button Head Socket Cap Screw 2. A set of M3 Flat...

Bolts to the side of the bottom 2020 extrusion on the Ender 5 Plus. My printer is enclosed on the sides so the 3mm tube that comes with the dryer loops around, goes through a hole in the side and feeds into a filament guide arm which then feeds up...

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

I've been struggling to prevent the hotend cables on my Ender 5 Plus from getting tangled up in the printer, so I came up with a clever solution: designing a sturdy bracket that keeps the cable elevated out of harm's way. Since installing this...

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

... to increase the sides to 3mm instead of 1.5. I also increased the thickness on the mount for the Ender 5 Plus because I found that the original "wiggled" too much on my printer when mounted. ... I added two additional screws to the block as well.

Inspired by a fantastic video from Tripod in his garage, where he provides an extremely detailed walkthrough of installing Bigtreetech's SKR 1.4 into an Ender 5 Plus, based on KAY3D's Cheetah 5.0 Marlin Firmware. Since I had acquired several SKR 1.4...

This endoscope mount has been modified to fit Ender 5 and Ender 5 Plus printers with the same front fan shroud as Creality. The mount doesn't obstruct airflow or interfere with the fan, allowing for smooth air circulation through the printer. It...

Work in Progress Remix of the TeachingTech Concept: Please note that this concept differs from the original due to the specific format of the Ender 5 Plus! To build a case for the Ender 5 Plus, you will need: - 4 V-slot profiles of 495mm - 4 V-slot...

Perfect mount for the Reolink E1 on the Creality Ender 5 Plus Fastening material: 2x cheese head screw M4 x 10mm 2x hammer nut for 6mm nut. Thread M4 Attention! ...I printed it out of PLA, if you often print ABS or ASA with a enclosure, please...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

The official Creality all-metal extruder upgrade (Pictured) sits slightly wider than the standard plastic Ender 5 Plus extruder, causing the filament exiting from the filament runout sensor to misalign with the new metal extruder. I created a...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

I'm using it on my ender 5 plus inside the enclosure to monitor both temp and humidity in there. It mounts with 2 m5 screws and a couple Tnuts. Step file included for those of you that need or want to modify it. ... Be sure to use support when...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

Namely: https://www.thingiverse.com/thing:4437226 https://www.thingiverse.com/thing:4492841 This fan duct will fit over the original BLTouch mount and the X Axis belt on the Ender 5 Plus WARNING This will push your part cooling fan right about 1cm. I...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...