ender 5 plus upgrades 3d models

You need to connect the Ender 5 plus hotbed wires to the nearby linear bearing. ...Adjust the height according to where you attach the wire, whether at the top or bottom of the bearing.

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

A bracket that support a BTT TFT24 display inside the housig of a Creality Ender 5 Plus. Raplacement of Creality TFT touchscreen. ... Downside of this design can't use USB and SD-card slot

Remixed the clip from kbrouder to hold in the rails of the Ender 5 Plus a little better. 

Ender 5 plus 2.3kg spool holder. Works with 0.75kg and 2.3kg spools. 50mm Diameter 105mm Width Mirror 3DS1 for dual setup. ... Works with the original hardware from the standard spool holder (one in each holder)

I'm implementing a Simple Patch for the Ender 5 Plus Filament Sensor. ...The Problem is that it's registering a False Empty Reading whenever the sensor gets nudged aside by the filament.

This is an Adapter for the tubing of the Polybox to connect properly with the Ender 5 Plus. ... This is A Remix of the of the Design by Doloth https://www.thingiverse.com/thing:4249749

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

Filament tube guide for the stock extruder setup on an Ender 5 plus. This support angles the tube at 10 degrees towards the bed. ... Hardware: 2) M3x16 screws 2) M3 t-Nuts

I couldn't get the original spacers to fit the bearings on my Ender 5 Plus. I broke several trying so I resized the spacer to 15.99mm. ...Now it slips on with a tight fit and stays in place.

I took GenMatthius' innovative Dial Indicator Holder design and adapted it to perfectly fit the Ender 5 Plus fan housing, capitalizing on its versatility to deliver a customized solution for the community.

Ender 5 Plus Z-axis supports. Has slots (for flexibility) for M5 screws with a counter-bore for flush mounting. ... The bearing used is a 608, in this case a ZZ as I had them already.

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

Will need some sanding and epoxy. ... Epoxy the Air Director to the Air Director Cover. The "tall" version can be used to keep the wires off the bed (Ender 5 Plus)

If you have an Ender 5 Plus with a Wham Bam bed, you can use this stl file and image to set it up in Prusa Slicer. Print instructionsNo printing required

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

Adapter bracket for an SKR 2. ... Made for Ender 5 Plus, could fit others. I used a SKR 2 but should fit 1.4, 1.3 also. ... Has wire tie down points at the bottom.

Here's a custom foot I designed for the Ender 5 Plus, printed with Cura Slicer. ... If you find this helpful, consider donating an amount you deem fair via PayPal to help offset my time spent on the design.

... pins, while five millimeter C'Bore holes enable secure fastening to 20mm extrusion. A thoughtful addition is a central hole for cable tie organization. We're thrilled you like this design and encourage you to print one for your Ender 5 Plus today!

Habe höhere Füße für den Ender 5 Plus konstruiert um einen besseren Luftfluss für die Kühlung zu gewährleisten. Sie sind ans Original gehalten, nur höher. Sie können eventuell auch an andere Ender Modelle passen, aber ich gebe keine Garantie. Nach...

Habe höhere Füße für den Ender 5 Plus konstruiert um einen besseren Luftfluss für die Kühlung zu gewährleisten. Sie sind ans Original gehalten, nur höher. Sie können eventuell auch an andere Ender Modelle passen, aber ich gebe keine Garantie. Nach...

This is an STL of the MicroSwiss Direct Drive Extruder plate for the Creality Ender 5 Plus. The STL was provided by MicroSwiss. ... I highly suggest buying it from them:...

Dial Indicator Mount designed for the stock fan shroud on the Ender 5 Plus. Print with the X flat on the build plate. Designed to print on the Ender 5+ without supports. If you have any ideas on how to improve this mount let me know in the...

... and end over the motor to mount standard 15mm x 15mm drag chain. ... It fits my ender 5 plus but will work for the ender 5 aswell. ... I used the chain trays from https://www.thingiverse.com/thing:4164988 It was printed in PETG and 30% infill.

Ender 5 Plus Y Axis Tensioner. Also recommend to print this belt Guide, while youre on it. https://www.thingiverse.com/thing:3968980 This is a Remix of files you need for Ender 5 + to make a Belt tensioner. ... You have all the parts you need from the...

This is almost the same size as the stock Ender 5 Plus holder, maybe 2 mm shorter. It works on the Ender 5 Plus, and the Ender 3 v2. It should work with other models as well, but I have not tested it. You will need two 608 bearings. ...You can use...

Simple Gcode for setting paper gap on 4 corners plus center of Ender 5 Plus HEAT BED AND NOZZLE TO PRINT TEMP BEFORE USING THIS TO SET PAPER GAP Print the squares to test your gap if you want. Follow CHEP's video on the Ender 3 to see how to use the...

Created for a friend who bought an Ender 5 Plus and changed the extruder to gerared dual drive BMG on recommendation. Modeled from the ground up according to own measurements. ... Printed on my Ender 3 V2 with Phaetus DragonFly BMS and still :-( stock...

This is an Adapter that allows the installation of a BTT Octopus 1.1 (and also 1.0) and the Stock MOSFET that comes with the Printer into the case of the Ender 5 Plus. ... If you want to be able to access all of the Ports of the Octopus, you need to cut...