ender 5 plus upgrades 3d models

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ... Will Need: 10mm Magnets ...

This display holder was specifically designed for a Big TreeTech TFT24 V1.1, allowing it to be mounted in an Ender 5 plus. ...To install the new holder, removal of the old display is necessary so it can be easily seated.

Im Rahmen meines Ender 5 Plus Umbauprojektes, musste ein Adapter für die neue SKR 1.4 Turbo Platine. Der Adapter hat noch eine Halterung für die SD Verlängerung von Creality. Für die Montage werden, 3 M3x8 Senk, 4 M3x16 Zylinder und 4 M3x6...

This is a DIN rail mount for the Ender 5 Plus MOSFET.  It is a snap fit and requires no hardware to mount the MOSFET, though M3 screws could be used if you want.  I printed mine out of PETG for a bit of flexibility. ... STEP file included incase you...

This mount seamlessly integrates both the BLTouch and filament run out sensor that come standard with the Ender 5 Plus. It attaches securely to the stock metal mounting bracket, so I'm confident it will be compatible with every printer in the Ender...

This was made specifically for the Ender 5 plus with the extruder gear that DOES NOT have a set screw. The original gear comes off relatively easy if you get some WD-40 into it, let it sit, the put the motor in a vice and use a prybar (gently) to...

After nearly a year of using it on my CR-10 without any issues, I decided to upgrade to an Ender 5 Plus and made a minor tweak to accommodate the new printer. I'm confident that this design will fit similarly designed printers and other Creality...

This fits the Ender 5 Plus but should also work with other printers with the same hotend housing. Notes: - You'll need 2xM3 20mm screws and 2xM3 nuts to attach the 4020 fan to the adapter. ... - Reuse the M2.5 mounting screws and air duct to attach...

A few changes were needed to get this to fit on my Ender 5 Plus. I went with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports .

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...

The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. Uses M3x8mm to attach to brass nut and M3x10/12mm to attach to Z Gantry Bar. Print Settings...

Its a remix for the Ender 5 Plus... the original version is for the Ender 5... it is also aligned based on the stock hot end... it may work with other hot ends as well,.however mine is the stock and this works great. I printed it in PETG at 100%...

This particular design was tailored for my Ender 5 Plus, but it can also be adapted for mounting the Quickcam 9000 webcam on other printers if they feature a horizontal 2020 beam running in front of the print bed. However, the suitability may vary...

This Direct Drive adapter is specifically for the following combination: Ender 5 Plus Ender 5 Plus HBE X-Carriage (I.e. https://www.ebay.com/itm/275391668537) Creality Spider hotend Wanting a direct drive to fit with the above and std MK8 extruder ...

To power this LED strip holder, I employed the Ender 5 Plus's built-in power supply, supplemented by a simple dimmer to achieve the desired brightness levels. ...For added versatility, I also created an enhanced version of this design with increased...

I made this tool carriage the same length as the stock Ender 5 Plus's tool carriage, with similar 'hooks' to continue to use the stock belt with it's crimps. STEP file is include if folk want to adapt it to their own machine. ...Unfortunately,...

This is a mount to allow you to put a BTT TFT35 v3.0.1 screen in the Ender 5 Plus. It is slightly recessed so that you don't have to cut a notch in the opening for the dial. Have not tested a print yet. Simply printed the original and noticed some...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. ...After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints.</p> <p>Will Need:<br/> 10mm...

I've taken some time to develop the Ender 5 Plus screen mount for the TFT35 E3 v3.0 display from BigtreeTech. Now you can replace the Creality touch screen and update the firmware to Marlin 2.0.x Just define the display as a Reprap Discount Full...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

Suitable for Ender 5 plus with stock frame, carriage and Creality supplied cable cover. ... Video: https://youtu.be/mEacAYde8OE You can find the Direct drive filament guide here: https://www.thingiverse.com/thing:3872001 Voron Afterburner :...

Purchased a Winsinn Dual Gear Extruder for my Ender 5 Plus, however the filament coming out of the filament runout sensor no longer lines up properly with the filament hole into the extruder. This mount will line the filament holes up properly. ...

I successfully installed it on my Ender 5 Plus, but it should also work seamlessly on the CR 10S PRO V1 or V2. The same bolts are utilized for this purpose. ...If you want to achieve even greater stability, I highly recommend using two metal inserts...

I created something quick to fit on the stock Ender 5 Plus hot end mount. There is an option for a pass through for the Bowden tube. Happy to provide more details if folks like this design End Caps for Open V-Slot 2020 with Open Hardware logo. ...

Designed to replace the stock Filament Sensor that ships with the Ender 5 Plus. Should line up perfect with the existing hole pattern under the extruder. I used a brim but supports shouldnt be needed. 10-15% infill should be fine. If you plan on...

This is a small modification to allow for the clearance for the BTT SKR E3 Turbo in the Ender 5 Plus. The hardware is the same for mounting, as mentioned you should use inserts or nuts with the mounting bolts. This also assumes you have made...

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

Made a mashup of my previous remix for the ender 5 plus and the mini satsana for the ender 3 (Ill credit when i can figure out which one) You will need to add custom supports under the two risen areas for the BLTouch mount. otherwise no other...

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. You have to ad support to the holder but not to the...