ender 5 plus upgrades 3d models

12864 LCD mount- the file I uploaded I added some support to the corner because his filed bends when you press the buttons https://www.thingiverse.com/thing:3421238 hot end drag chain https://www.thingiverse.com/thing:3132855 Ender 3 Cable Chain E...

To print: Ender 5 Normal: ---------------------- Ender 5 and 5 Plus RAILMOD - Tensioner Side v2.0.stl Ender 5 and 5 Plus RAILMOD - Motor Side v2.0.stl Ender 5 RAISED RAILMOD - Bearing Bracket v2.0.stl Ender 5 RAISED RAILMOD - Carriage v2.0.stl Ender...

This is a mount to allow you to put a BTT TFT35 v3.5 screen in the Ender 5 Plus. ... It is slightly recessed so that you don't have to cut a notch in the opening for the dial.

A simple cover for Ender 5 printers that simply rests on top of the LCD. Not hinged, nor snapped-in, as I thought those designs were too bulky and dorky. The more infill you choose to use, the more light it will block. ...Optionally, you can paint it...

Two M4 threaded nuts are required, along with two M4x12 screws. ...Additionally, one Ender 3 LCD display unit, complete with mounting screws, is necessary. ...Furthermore, two LCD cables will need to be procured for this project.

This mount makes it easy to install a BTT TFT35 v3.5 screen on your Ender 5 Plus. ...The mount's design keeps the screen snugly in place, eliminating the need to carve out a notch for the dial, allowing for a smooth and seamless installation process.

For the Ender 5 Plus, you need to use the risers, which attach to the bed assembly crossbeams with T-Nuts and capture the tram wheels. I designed these risers to accommodate up to a 12mm OD spring, so feel free to use 30mm medium loads. You will...

The original STL's had the tool head sitting too low, causing my BL Touch to collide with the Ender 5 Plus bed rails. The tip on my BL Touch was sheared off, luckily its still usable. The fan duct would also collide, so I had to adjust my x...

English Upgrades for Hellbot Hidra Plus and 220. It has 3 parts. 1 - Support for filament sensor (left and right) + front (VGA cable support). 2- Support for spool, to put it in front and the filament goes down straight. It depends on how you put...

This is a summary of the parts and hardware I used to upgrade my Printrbot Plus 1303 (2012-era) closer to today's standards. I will be sharing my progress at MRRF 2019. Here are the upgrades that I purchased from Printrbot: - Aluminum bed with...

It is fully printable without any supports and uses the existing sheetmetal mount on the Ender 5 Plus. I designed the bearing with a smaller diameter than the inner diameter of the spool and added a bushing to ensure compatibility with different...

My Ender 5 Plus is a great printer with a very rigid frame. Problem is, my apartment doesn't have a single level floor in the building. My printer is lopsided and that gave me strange artefacts in printing. So I designed this to keep the lower half...

Ender 5, Ender 5pro, Ender 5plus and possibly the Ender 3. Only fits the Stock hot end plates. Slips on tight no screws or disassembly required for this simple mod. Settings if using a Micro Swiss hot end and hardened steel nozzle Most settings...

... the frame. My extra light cooling shroud for ender 5: https://www.thingiverse.com/thing:6079627 My BMG direct drive mount: https://www.thingiverse.com/thing:6079570 Design inspired by the original Satsana: https://www.thingiverse.com/thing:4528533

... plate. Attn: Use a crew that is not too long otherwise it will touch the frame. Link to my direct drive mount for BMG: https://www.thingiverse.com/thing:6079570 Link to my dual 5015 fan duct for ender 5s: https://www.thingiverse.com/thing:6079533

Uploaded BMG mount for standard V6 to account for the BLTouch Recreated in fusion for my Ender 5 Plus, as Creality has slightly modified their hotend carriage. It should fit the other Ender 5, Ender 3 and CR10 series as well as they all have...

It is an adapter for Duet into Ender 5 PLUS.

For mount Duet Wifi board to Ender 5 Plus.

It is an adapter for Duet into Ender 5 PLUS.

Creality Ender 5 Plus https://creality3d.shop/collections/ender-series-3d-printer/products/creality3d-ender-5-plus-3d-printer Palette 2s PRO https://www.mosaicmfg.com/pages/products Bondtech DDX v2...

I upgraded to a dual gear extruder on my Ender 5 Plus and the alignment for the filament sensor was off. This is a 10mm Spacer that aligns the filament sensor for the all metal dual extruder found on amazon. ...

hi everyone this is the first upgrader that i thing will be good fro your Ender 3 skr 1,4 t tmc 2209 tft 3.5 v2 titan direct extruder and cable management (dsub 25 pin) for d sub you need to print it with nozzle 0.4 layer high 0.2 all the rest is...

This is a remix of https://www.thingiverse.com/thing:4670117 This wil fit with an embedded nut soldered in M5

Using the stock hardware, this remix keeps everything aligned and the stock nut from turning.

Using the stock hardware, this remix keeps everything aligned and the stock nut from turning.A stronger part from this collection:https://www.thingiverse.com/thing:4922335Category: 3D Printer Parts

Français Clip pour cacher le câble USB de la caméra dans un Profilé Aluminium 20x20. Il est simple mais efficace. Il suffit de régler la longueur dans votre slicer. J'espère que cela vous servira. English Clip to hide the camera's USB cable in a...

Français Clip pour cacher le câble USB de la caméra dans un Profilé Aluminium 20x20. Il est simple mais efficace. Il suffit de régler la longueur dans votre slicer. J'espère que cela vous servira. ...

Direct Modification Filament Supply Resistance Reducer, It's a Spool Holder. This device reduces the resistance of the filament supply during direct modifications. ... Visit this link for more information: https://www.thingiverse.com/thing:4063448

Use it to set the heigh of every foot on a non planar support.

Customized version of https://www.thingiverse.com/thing:2280529 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2280529