ender 5 plus upgrades 3d models

Ender 5 Plus Bowden tube & cable guide =============================== I was frustrated and annoyed because of the inconsistend layer print behavior which lead to bad looking surfaces. I managed to find out, that this was related to the...

# Ender 5 Plus Case Replacement A remix of @Moederbeer case, I wanted to remove the large E5+ case enclosure and put the parts in a different container. I looked at a lot of cases, but couldn't find one I liked so I ended up creating this new...

This is my remix of Satsana, I found this is a really nice project, just needed some tweaks to make it fit better on Ender 5 Plus, corrected the locations to not hit the belts not even the Y axis on the right side. Printing it with 3...

This is to mount a Duet 2 Wifi and paneldue in an Ender 5 plus positioned in a way to get maximum Wifi signal. ...you will need to move the mosfet to do this mod, use:</p> <p><a...

Update: - Added a V2, just slightly bigger holes for the bolt and allen key making them easier to fit Purpose: - Liked the original, but like requested in the comments for it, I also wanted M5 fitments - Removed internal filleting and recess -...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

I am currently working on turning my Ender 5 Plus into a high temp filament machine. In that endeavour I realized that I would have to move all my electronics outside the main body so that I can use 1/8" acrylic in the frame as an enclosure. So I...

This is a bracket to relocate the front crossbar of the Ender 5 Plus to get a better view of the build plate. You may locate the crossbar at any height you find suitable for your setup. Also consider printing the End Covers that protects you from...

Made this for ender 5 plus to attach cable chain to extruder in a direct drive setup. I could not find anything with key words to find something. So I made it. This is just the brackets to mount cable chain from...

This is a dial indicator mount for the Creality Ender 5 Plus. I didn't originally make this but I modified an existing one I found on Thingiverse from a Creality CR-10. This is an extremely accurate way of leveling your bed. Using this and a good...

I used these to help stabilize the long 2020 extrusions to the 2040 extrusions on my Creality Ender 5 Plus. These can be used on any frame that incorporates the 20 series extrusions. I uploaded multiple variations depending on your preference. There...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install this...

To modify the Ender 5 Plus you will need the following: 3x 450mm MGN12H rails 3x MGN12H bearings 66x M3x8mm bolts 66x M3 T-Nuts All the above will cost about $120 or so. Print 2 of the Linear_Rail_Adapter_V3 For the X-Axis you will need M4 and M5...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a piece of double sided tape between the adapter and the 2020 extrusion (probably not needed). It allows access to the USB...

Update: - Added a V2, just slightly bigger holes for the bolt and allen key making them easier to fit Purpose: - Liked the original, but like requested in the comments for it, I also wanted M5 fitments - Removed internal filleting and recess -...

I upgraded my E5 Plus to a SKR Mini E3 V2.0 and the Bigtreetech TFT V3.0. I printed this: https://www.thingiverse.com/thing:4421077, but the screw holes of the PCB didn't align, so I remixed it with M3 threaded holes, shifted 1mm from the place...

I accidentally printed a Satsana Version for the ender 3, which is identical to the ender 5 x carriage, except for the bltouch. ...It only needs to move about 3mm to the left to clear the fan duct, so rather than printing a entire new shroud, I just...

I accidentally printed a Satsana Version for the ender 3, which is identical to the ender 5 x carriage, except for the bltouch. ...It only needs to move about 3mm to the left to clear the fan duct, so rather than printing a entire new shroud, I just...

Ender 5+ Tool holder designed to fit on frame with no screws required. &nbsp;I printed the model as is with no support and 13% infill. ...&nbsp;&nbsp;</p>

Was ask to post my design from :- https://www.reddit.com/r/ender5plus/comments/ljqbks/loving_the_hemera_on_the_ender_5/ They are a little overkill , but if it isn't broke don't fix it .

The bracket thats been on our wheeled Ender 5 for a while, good printing machine. I recommend $10 pancake motor with it and a firmware current adjustment. ...Chain mount built in GROUP: https://www.facebook.com/groups/541547619887950

Hallo, habe zwei verschiedene Kabelboxen entworfen, um den Kabelsalat beim Ender 5 Plus dezent zu verstecken. Es gibt in der Box verschiedene Öffnungen. Die 2 Öffnungen die sich im Boden befinden sind für die Z-Achsen Motoren links und rechts. ...

Hallo, habe zwei verschiedene Kabelboxen entworfen, um den Kabelsalat beim Ender 5 Plus dezent zu verstecken. Es gibt in der Box verschiedene Öffnungen. Die 2 Öffnungen die sich im Boden befinden sind für die Z-Achsen Motoren links und...

Totally redesigned my LED bar for the ender 5 Plus. V1 of my LED bar was great, unfortunately since I had printed it with PETG and used LED strips with 5050 LED chips, it warped something fierce. The problem was the LED got too hot for the design....

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the...

I converted my Ender 5 Plus Extruder to a Biqu H2 direct drive. I wanted a way to have the filament feed from the top instead of through a bowden tube. I created an offset mount that can hold any filament up to 5kg. I wasn't sure how the filament...

Here is my own design for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with Linear rail. 2 x 5015 component fans, 4010 or 4020 Hotend fan, BL Touch bracket and cable routing to the top. Put the fusion file in here with it, anyone who...

Cross bar braces for the Creality Ender 5 Plus to stiffen up the frame a bit and lessen the top wobble caused by X and Y axis movement. It reduced the visible wobble quite a lot on my printer. Use any 8mm rod cut to 670mm +/- 5mm for the left...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...