ender 5 plus strain relief 3d models

Designed to use with Micro Swiss Direct Drive Base for Ender 5. As a bonus - now it is so easy to operate extruder's spring arm. Screwed to the base using 2x m3x12 screws Needed to attach a 3/4 inch [split wire loom...

The arm is a bit thin and there's a bit space to make it thicker, but seems to work for me so far, so I'm keeping it like this for now. Rotate on the flat site, so that it doesn't require supports Print Settings Printer Brand: Creality Printer: ...

On the male connector, I added a bit of super glue after to hold them in place as there is less area to hold them in place.I tested my prints with some generic XT60 connectors, and both fit the standard connectors with no modifications.I printed mine...

Used to relief tension on the screw terminals when using solid wire and when installing in tight spaces. I've had the wires pop out during installation a few times, this helped me prevent that. ... (hole in the side is for help with bending, not...

Used to relief tension on the screw terminals when using solid wire and when installing in tight spaces. I've had the wires pop out during installation a few times, this helped me prevent that. (hole in the side is for help with bending, not very...

hey i messed around with building a few remixes, stock fans for an ender 5 plus and micro swiss direct drive. ...hope this prints well WIP

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

USB strain relief for generic usb cables.

Strain relief for the hotbed cable for Ender 6. The hole behind the cap needs to be threaded, I recommend use taps and dies (M5) for this. ... 1x Bolt (M5 x 8mm) 2x Zipties

Designed this Hot end strain relief for the Ender series 3d printers. Ender 5, Ender 5pro, Ender 5plus and possibly the Ender 3. Only fits the Stock hot end plates. Slips on tight no screws or disassembly required for this simple mod. Settings if...

I designed a new strain relief system for my Ender 3 printer. The stock one, as well as others I've used, was difficult to level the bed because of the uneven spring that always stood higher than the rest. This issue is now resolved. To install the...

One of the hotbed connectors broke on my ender-2 so I made this strain relief so that it doesn’t happen again. It requires one cable tie (2.5mm or smaller) and m2 screw and nut. I think it best to disconnect the cable before installing so that you...

I wanted a strain relief bracket which didn't interfere with the bed levelling screws - instead, one that clamped the bed carriage would be ideal using m3 hardware The one I made is v1. This is version 2, featuring an angle to avoid screws contacting...

I needed a strain relief bracket that wouldn't interfere with the bed levelling screws - instead, one that clamped the bed carriage would be perfect using M3 hardware. The one I designed is v1. This is version 2, featuring an angle to prevent screws...

This is a remix of the Ender Ender Heated Bed Wire Restraint by Ender Extender. I liked the design but did not like the idea of relying on two sided tape so I added holes for bolts. Also, the design allowed for quite a bit of play in the cable as...

... I'm focusing on upgrading its components that I believe require improvement. ... First up is a device designed to provide strain relief for the cables connected to the extruder. ...Installation is straightforward and easy to understand, in my opinion.

This is an Accessory for the Ender 5: A mounting bracket for the BL-touch sensor AND a cable relief for all the cables to the printing head. The assembly is a bit tricky, but no extra screws are required. (you need two screws for the BL-touch, if...

This is a 3D Touch V3.2 Pro mount for an Ender 5 with cable and tube strain relief.

... level. ...To start, I've identified a crucial enhancement that caught my attention - a device designed to provide strain relief for cables connected to the extruder. ...Installation is straightforward and intuitive; it's clear what needs to be done.

This is a 3D Touch V3.2 Pro mount for an Ender 5 with cable and tube strain relief. Category: 3D Printer Parts

This is a remix of https://www.thingiverse.com/thing:4632689 Added some distance on the clip. ...If you have the Creality BLTouch metal bracket this should fit perfectly! This should work on an ender 3/3 pro as well. ...

Ender 6 Hotbed Cable strain relief

... you could easily use it with a GoPro mount by lining up the mounting holes. Note that since this is supposed to provide strain relief and hold everything in a crash it is a very tight fit and may take some effort to get it around the connector.

But to hopefully prevent another fatigue break in the future, I designed this clip to which you can fix the heater bed lead by means of a cable tie and thus relieve the strain. Because it gets quite warm in the area, PLA probably won't be...

Ender 6 Front Cable Strain Relief original was pretty rubbish

Wire organizer Wires on my Ender 5 were too short to secure against the frame so I created a set of interlocking panels. You need 2 top panels, 1 corner panel and 1 Ender port panel with t-nuts and 5mm crews. Also added a spool holder riser to fit...

Remix of [Ender 5 Direct Drive Strain Relief (Enomaker)](https://www.thingiverse.com/thing:4407360) to fit the [ENOMAKER Direct Drive Extruder](https://www.amazon.com/gp/product/B08399KX3X/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1) The...

This is a strain relief for the bowden tube and cable bundle for a Creality Ender 3 V2. This uses the existing screw for the hot end shroud on the back side of the carriage. I didn't like the way that the tube and cables were unconstrained at...

Just a couple of strain reliefs for the ender 6 the printed ones that came with were pretty rubbish.

Strain relief for the tool head / x-carriage cables on the Ender 3 printer series.