ender 5 plus strain relief 3d models

Remix of Giuliano Moschini's fanshroud assembly for the MicroSwiss Direct Drive for the Ender 5 Plus. I trimmed it down if someone wants just a strain relief. I added channels for 2.5mm smaller zip ties. I printed this on my CR-20 Pro with a .2mm...

Uses a single m3 screw. ... Print with no supports.

I prefer straightforward solutions that don't require any specialized equipment or modifications. This design fits snugly in place without needing anything removed, making it easy to implement. Since every printer is unique, you can use a small piece...

This is a remixed ender 3 strain relief that will now work for an ender 5 plus

Strain relief and support stanchion designed for the Ender 5 Plus, but should work on Ender 5 and Ender 5 pro (anything using the same carriage) Filament guide tube and corrugated wire guide snap into dedicated clips at each end that fasten to the...

This is a revised version of an exceptional Ender 5 Plus Heat Bed cable strain relief. It prints quickly and functions flawlessly. However, additional hardware - M3 screws and T-nuts - are required. T-Nuts can be found at...

A custom strain relief for the Ender 5 Plus extruder, crafted with precision using PLA and optimized settings from the factory slicer. To bring this design to life, you will need: 1. An M3 x 12mm Button Head Socket Cap Screw 2. A set of M3 Flat...

Remixed from another design that would interfere with the carriage endstop on Ender 5 Plus. ...This one has been modified to fit properly and is working perfectly on my Ender 5 Plus.

Basic screw on X-axis motor strain relief. ... Print horizontal and you'll need M3 screw + nut.

You will require an M3 screw and a nut to secure the basic screw-on X-axis motor strain relief, which should be printed horizontally.

Designed to support the heat bed cables to help take some of the strain from the solder joints of the cables when bed is at the high positions. Undo the 4 pcs m4 screws holding the linear guide bearing, slide it between the guide bearing and...

Cable strain relief for Stockman59's Hero Me Gen5 mod for the ender 5 plus with Microswiss DD. Use M3 x 8 or 10mm, not sure which ones fit. Has 2 slots for small cable ties to thread through. ...Print on its back (so the curved surface where the cables...

Wire strain relief on an Ender 3 V2 and Ender 5 Plus. Will work with other Ender machines. ... Best used with the Duke Doks V6 BMG mount: https://www.thingiverse.com/thing:4808299 Print with supports everywhere.

This is a remix of @joshkennedycouk remix of another Ender stock head bowden tube and wire strain relief. Sliced with Prusa Slicer 2.4.0 Block Modifier added for more infill in the clip stress area. Print time 2:46 using PETG Head temp...

I liked the original design of this but was unable to get the original piece to fit around my machines bearing sleeve so here's my take on the DIYPark original. Additional length was added to the main arm along with a larger bearing sleeve ID.

I changed this up to have a bit more on the end of the arm. I hate when a design is cut off. It looks weird. I also made the mounting holes for M4 flat heat screws, as that was what I had on hand. ...I T-nuts are also from the filament sensor that...

I added some height and support to the cable doesn't drop/sag as much. ... This is a remix from https://www.thingiverse.com/thing:3937920

I needed a taller version to prevent my cables from hitting the homing sensors. ... Feel free to make changes.

This bed wire strain relief device is designed to mount to the 2020 extrusion that makes up the bed support on the Ender 5 Plus and mounts using M5 bolts and 2020 t-nuts and secures the wire with a zip-tie. ... No disassembly of the bed or any other...

A customized strain relief for the bed of an Ender 5 Plus. Printed using PLA and optimized with a factory slicer. The requirements are as follows: Two T-nut_M3 (thing:3050607) parts. Two M3 x 20mm Button Head Socket Cap Screws. Two M3 x 12mm...

I wanted something to hold the cables and split loom vertical. ...My speeddrive remix uses similar holder. Printed on Ender 5 Plus.

<p>Mount this above your x-axis motor for a spot to zip-tie the cables.</p>

##This is a strain relief for the print head cables on the Ender 5 or Ender 5 Plus. It just snaps on and add some cable ties. ##For the latest on this project and others, join my group:# https://www.facebook.com/groups/3DPrinterModding/ All...

To relief cable strain while printing.

I have made different remixes and think the one I put stl of is the best of all the ideas I had. ... This suits Ender 5. I have not tried this on other printers. ...

This is a remix of thing 3591391 that adds the ability to zip tie the cable loom and Y adapter of the 3D Chameleon to the hotend strain relief preventing any bending of the short tube that goes into the hotend as well as adds cable support along the...

This is a cable support bracket for the hot bed cable on an Creality Ender 5 PLUS. Parts: 2 - M4 Nuts 2 - M4x25 Socket Head Cap Screw 2/21/2020 - Added one that is 50mm taller by request. 2/10/2020 - Added V2, Same as original except...

I couldn't find a cable strain relief for the Ender 5 Plus hot end, only for myEnder 3 Pros so decided to make and share my own. I made mine from Technology Outlet PLA but any material should work. Printed on a Creality Ender 3 Plus upright...

This Remix is a cable support bracket for the hot bed cable on an Creality Ender 5 series with the Ender Xtender Upgrade. I redesigned this for the 500x500 bed, but it will work fine for the 400x400 bed. ... Parts: 2 - M4 Nuts 2 - M4x25 Socket Head...

This Remix is a cable support bracket for the hot bed cable on an Creality Ender 5 series with the Ender Xtender Upgrade. I redesigned this for the 500x500 bed, but it will work fine for the 400x400 bed. ... Parts: 2 - M4 Nuts 2 - M4x25 Socket...