ender 5 plus noctua fans 3d models

A replacement case cover for the Ender 5 Plus, allowing you to mount two Noctua 92mm fans to keep the system cool, and quiet. The main reason I did this was to prevent the power supply fan from turning on, as it's louder than most commercial...

At https://www.thingiverse.com/thing:4821969 jerryfudd designed a Ender 5 Plus Power Supply Casing Noctua 92x14mm RSP-500-24. ...I made this remix so that the openings fits for the new Noctua fan.

Here are 2 Axes Fans Carriers for printer Ender 5 plus. They are design for Fan 92x92x25 / 220-110 Volt able on AliExpress for example. That's perfect to decrease the temperature of Axe motor specially when you print for a long time. ... You can...

Fanshroud for Noctua 4020 fan on Ender 5 Plus. Should fit several other printers too. Print as picture from Cura, circles down to plate, with supports ! ...

hey i messed around with building a few remixes, stock fans for an ender 5 plus and micro swiss direct drive. ...hope this prints well WIP

https://www.thingiverse.com/thing:2802474 Lastly, you will need to elevate the Ender 5 Plus with bigger feet so the fans have room to move air. These are a cool design that use squash balls to limit vibration ...

This adapter plate replaces one of the noisy default 40mm fans on the Ender 5 Plus bottom plate as well as having a convenient spot for the buck converter. It reuses the same 4 screws that the original fan came with. Parts: 2 x Nuts #4-40 x 6mm long...

Purpose: Fitted the Meanwell RSP-500-24 and wanted a silent fan, also wanted to aim the fan closer to the stock grills - may cut this to better fit the 92mm later Notes: - I'm using this alongside my own design RSP-500-24 adapter, this will likely be...

Purpose: Fitted the Meanwell RSP-500-24 and wanted a silent fan, also wanted to aim the fan closer to the stock grills - may cut this to better fit the 92mm later Notes: - I'm using this alongside my own design RSP-500-24 adapter, this will likely be...

I removed the no longer needed stock display and added this block and two Nocturna Ultra quiet fans. ...Size 60mm by 25mm. used the 12 vdc version and added the buck converter. These are real quiet, only fan I can hear now are the hot end fans.

I made this remix to fit the ender 5 3d printer. I liked it because of the shape, the bl touch support, and the fact that you can keep your stock fans. Printed it in black pet-g, 0.2mm and 20% infill with tree supports. You need one slightly...

Noctua fans I used for the MB and PSU: Noctua NF-A8 FLX (80mm) I printed both parts (MB and PSU cover) in PLA. PS: If you prefer to add a fan cover - here you go: https://www.thingiverse.com/thing:4837562 Btw. ...you also need those feet to lift up...

Noctua fans I used for the MB and PSU: Noctua NF-A8 FLX (80mm) There's also a mount built in to fit a LM2596 buck converter (43mm x 21mm) I printed both parts (MB and PSU cover) in PLA. PS: If you prefer to add a fan cover - here you go:...

... This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro. The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the Mosquito's.

This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro.The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the Mosquito's. If...

... into the case, and the front 2 blow out of the power supply and case. After this upgrade I never have had my power supply fan activate. I am using 120x120mm fans from Noctua. ... Note: You need to print 4 stilts so the fans have enough room to blow.

Ender 5 plus bin

Simpel improved fan duct, exchange with standard one. ... Print without supports in vertical position

Simpel improved fan duct, exchange with standard one. Print without supports in vertical position Category: 3D Printer Parts

perfect fit to ender 5 plus V2 https://cults3d.com/en/3d-model/tool/ender-5-plus-drawer-v2

This is a Cable Holder desigend for the Ender 5 Plus.

My goal was to keep the original look of the printer and avoid the need to print a whole new base-plate for my Ender 5 Pro.This design is an exact copy of the original power-supply cover (where the fan is attached) and features a hole where a Noctua...

The noctua being higher than the old fan, it was necessary to slightly raise the power supply cover. You will need to use M3 screws. Personally I used four: M3:4 and four: M3:8. There is however a small defect to that, the cover of ender does...

Creality Ender 5 Plus model. ...Currently a work in progress and will be updated as I work on it Many parts derived from this model: https://grabcad.com/library/creality-ender-5-pro-1 Last updated 8/10/20

This is a model I created of the Creality Ender 5 Plus. ...I use this to design add-on parts and enclosures.

Enclosure for a Ender 5 Plus, work in progress, will update as I get more completed.Material is 2mm Aluminum, if needed I can upload the DXF flats.

This is a design for a bed levelling on an Ender 5 Plus 350mm x 350mm bed. The design has a height of 2mm. ... I have a complete bed levelling guide here - https://mattharmer.me/correctly-level-a-creality-ender-5-with-bl-touch

Printer needs extended feet my design is here https://www.thingiverse.com/thing:5363599 required, Noctua 80/25 fan Buck converter M3 insets x4 30mm M3 bolts x4 cable for switch change electrical connectors I got totally fed up with turning my...

Hintergrundbild für Euren Ender 5 Plus.1.Datei in Cura einfügen (Programm nicht öffnen)( C:\Program Files\UltiMaker Cura 5.3.0-beta.2\share\cura\resources\meshes)2.Befehl im Ordner definitions in der Ender 5 Plus Datei hinzufügen und speichern.(...

I made a toolbox for the ender 5 plus. My tools where everywere so i hope you can use this as well. You have drawer for extra space. and on top for all the tools. ...You also have space for aech spear nozzel from 0.2 to 0.8.