ender 5 plus mods 3d models

This is an adaptable upgrade for the Ender 5 Plus featuring directional guidance to fine-tune your print bed, which can also be compatible with the CR-10S Pro.

A simple block riser I put together to handle adding on NEMA Z Dampers to my Ender 5 Plus. ... This doesn't change the supported Z print area as it doesn't change the coupler configuration.

This is a remix of the original mounting plate. ... This was changed to both give a better wire strain relief post and to allow it to mount on the Ender 5 plus carriage plate without hitting the left belt tab.

I didn't create this from scratch. ...The original work was done by dinesh612. They put in all the effort. My contribution was adding the Crealty Dragon and the Ender 5 Plus content to it.

Screen cover for ender 5 plus. Fits perfectly right in the ridge around the screen. ...I would print in black to completely block out the light but white filament makes for a cool effect.

i have moved the position of the cr touch mount (witch also works with Bl touch i run one) to the oposite side of the tool head to maintain the ender 5 plus position the base plate and cr touch mount and wire cover are different. also have...

Fusion 360 model: V22 - https://drive.google.com/file/d/1-9BK0u-uTyg5o4LtAJwfTBewd1Gzkn0r/view?usp=sharingChanges:V22 - Added some beefed up feet because I have a small desk smaller than the printer dimensions.Thank you to Zane Kincaid for making the...

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

This adapter makes it possible to fit a SKR 1.4 board into an Ender 5 plus without cutting a hole in the case. ... Hardware required: 4 x 3mm screws When its printed, you take a 2,5 mm drillbit and drill the 4 four holes for the SKR board and the screw...

Originally it was remixed by https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus this specific is remixed from remix created by PUCK81...

Filament guide for my Ender 5 plus, have my spool mounted on the side but the filament was making a 45 degree angle into the filament sensor. Not good. Made this to make sure filament enters at a more perpendicular angle. Mounts on stock Ender 5...

Simple design to cover the LCD screen on the Ender 5 Plus. I no longer use the touch panel on the printer, as I use Klipper. I added my own custom logo on my original print, but created a blank panel and one with the Ender logo to share. To get the...

Pattern to see which corner needs to be set with Ender 5 Plus. Set your layer height to 0,2mm and you will have 2 layer. For bed equale or larger then 350mm x 350mm. ... *** WARNING*** Paper clip of the front left corner must to be move to...

The Ender 5 Plus can be elevated by placing this foot under it, utilizing the stock feet provided. The foot features a tapered recess at the top that cradles the stock feet in place, preventing them from slipping or tilting. ...With this riser...

This thing was created using Tinkercad. ...Edit it online at https://www.tinkercad.com/things/b8Y8tFp5kVM. This is a remix of the original design, modified for use with the Ender 5 Plus. ...Simply remove the top bar to enable smooth sliding motion!

Ender 5 Plus filament guide enables effortless spool movement outside the printer for enhanced accessibility. A secure attachment is ensured by zip-ties tied through a sturdy tube. ... Print time on standard settings typically ranges from two and a...

The workbench I wanted to set my ender 5 plus up on was a bit smaller front to back than the footprint of the printer, so I made this doohickey. Just shove it under the feet along the edge of the surface it should accommodate the overhang. ... Use...

These Are some Holders i designed for the Ender 5 Plus to prevent the Glas Plate from slipping. The Holders for the Front and the Back easily Clip onto the Bed and its supporting Structure. ... The Holders for the Sides require to unscrew the Bed...

This holder consolidates all of the hex keys, wrenches, and the screw driver that comes with the Ender 5 Plus. It also has an extra slot to keep a razor blade in. ...The lid may be a tad loose depending on your printer, so you can add some tape to add...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%

I relocated the electronics enclosure on my ender 5 plus to sit outside my enclosure. There is a small fan on the bottom of the box that is designed to cool the electronics components inside, so these feet lift the box off the table slightly...

a simple low profile cable clip of the ender 5 plus hot end cable aka 1/2" split loom. ... for assembly: (2) M5x10 screws (2) M5 T nuts (1) 8" cable tie Second version to re-use shorter screws Tip: Add a second clip for added support

Summary This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket...

I just made this quick thing, it covers the metal sliders on the Ender 5 Plus the bed uses to go up and down evenly. Doesn't affect the way it works, just makes it so you can change the colour from a metal to what ever colour you want. ...It fit...

This is a remix for an Ender 5 Plus - will require 2 of these pointing at the printed object. ... Will be printing in the next day or two to test - any issues I will update this Printing on my E5+ using PETG as that is what I currently have it set...

Leveling feet for the Ender 5 Plus. A full set will require the following components: (2x) Part1-Mount-LH, (2x) Part2-Mount-RH, (4x) Part3-Foot, (4x) Part4-JamNut, (8x) M4x10 screws, (8x) M4 T-slot nuts. ... You can stick some foam tape or rubber dot...

I used the original spool holder ring lock bracket that came with my Ender 5 Pro and cut the part that holds the spool itself and kept the part that goes on the metal bracket as seen in the pictures. If you notice there is a hole in the lock ring...

I used the original spool holder ring lock bracket that came with my Ender 5 Pro and cut the part that holds the spool itself and kept the part that goes on the metal bracket as seen in the pictures. If you notice there is a hole in the lock ring...

Designed for the Ender 5 Plus, but should fit any printer that uses 20mm x 20mm rails. https://www.amazon.com/dp/B071F1K7BJ?ref=ppx_yo2ov_dt_b_product_details&th=1 Use with 1.75" in, 30-durometer, Sorbothane hemispherical feet. I bought the...

Original Model: https://grabcad.com/library/creality-ender-5-plus-1 The process for using it in Simplify3D: You would want to put the file into the folder: C:\Users\**USERNAME**\AppData\Local\Simplify3D\S3D-Software Then go into Simplify3D and go to...