ender 5 plus mods 3d models

This adapter is for mounting the BTT Manta M8P in the Ender 5 plus case. This places the USB, SD, etc ports in the vicinity of where the stock board positioned them. You will need to cut a hole in the stock Ender 5 plus case if you intend to access...

Remix of the ENDER 5 electronics mounting plate for Raspberry Pi. ... https://www.thingiverse.com/thing:4140386 Only cut down to fit the Ender 5 Plus with the offset PSU mount. ... Mounted in the case with some good double sided foam tape (3M)

Ender 5 Plus X axis Linear rail with a BMG direct drive. Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. Print instructionsCategory: 3D...

Two pieces that fit inside each other and squeezed tight with zip ties and attached to the frame with 2 x M4 bolts and T-nuts Update 01/04/2021: Thicker version added as 'Ender 5 Plus Rear Cable SupportV2.stl' Original...

I had received quite a few requests for a BOM of the items used to build my custom Ender 5 Plus. I gathered together everything I could find from the various sources used to make this mix and provide their links in the PDF contained in this...

I printed with 0.6mm nozzle with 0.8mm extrusion width and 4 walls and 6 top and bottom layers.Step 4:Use the two screw that was holding the stock creality hotend cover and use that to secure the adapter plate on to the back of the Creality Sprite...

Simple remix to allow the bracket to work with the Ender 5/ Ender 5 Plus carriage. The ender 5 plus belts are position so that the ferrules on the end stick out the front of the carriage. This modification allows space for those ferrules. ... You...

Whether you're a seasoned 3D printing enthusiast or just starting out, these custom-made feet can help take your prints to the next level and unlock new possibilities with your Creality Ender 5 Plus. Incorporating Squash Ball printer feet into your...

This is a side frame mount that I designed for the Palette 2S to attach to the Ender 5 Plus. The file was designed in Fusion 360 and printed in PLA with 30% infill. I attached the included Palette 2S mount to the printed mount using self tapping...

I'm employing it successfully in conjunction with a Bigtreetech SKR v1.3 board that's been mounted using a simple adapter; as you can clearly see from the images, this configuration will definitely fit inside the Ender 5 Plus case. ...To my knowledge,...

https://www.thingiverse.com/thing:2802474 Lastly, you will need to elevate the Ender 5 Plus with bigger feet so the fans have room to move air. These are a cool design that use squash balls to limit vibration ...

Ender 5 Plus Cooler =============== This is an Ender 5 Plus Cooler mount for two 5015 radial fans and one 4020 fan without any change to the BLTouch or the Hotend. Only modification required is to the fan connector cables. I suggest to use terminal...

... can install the box more easily. Print Settings Printer Brand: Creality Printer: Ender-5 Plus**Rafts:** Doesn't Matter Supports: Yes**Resolution:** 0,2 Infill: 20% **Filament:** Doesnt Matter Doesnt Matter Doesnt Matter Category: 3D Printer Parts

The one included with the kit is for the Ender 5 (non Plus) and did not line up correctly. Micro Swiss support sent me this STL and gave me the ok to Share it an post it here. ... Thanks to Micro Swiss support for supplying this so quickly and...

I prefer 3D printer accessories that don't need extra hardware, so I designed all mine to simply snap onto the 2020 aluminum frames of my Ender 5 Plus printer. This pliers holder snaps right on and stays put, keeping it within easy reach as I always...

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near the clips and twist carefully. Creality...

After nearly a year of using it on my CR-10 without any issues, I decided to upgrade to an Ender 5 Plus and made a minor tweak to accommodate the new printer. I'm confident that this design will fit similarly designed printers and other Creality...

Ender 5 Plus Exoslide Marlin Code Mod Infill = 100% NOTE for this Mod the Front Bar needs to be moved DOWN also the Exoslide is on the front screws on the X axis bar which the instructions say use the back screws Z offset changes depending on nozzle...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

Ender 5 Plus BTT smart filament sensor mount, this goes in the place of the stock sensor and uses the same M4 bolts and T nuts. ...Wire management for the hot end wiring to bring the wires off of the back extrusion to make way for top enclosure.

This is a rapid and makeshift spacer designed to enable an E3D Hemera Bowden to be securely attached to an Ender-5 Plus printer. ... It shifts the stock filament sensor away from the extruder bracket, allowing its filament path to align perfectly with...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

This gasket has the screw holes oversized and spaced to fit the stand-offs in the Ender 5 Plus's case. ... I noticed a slight whistle and visible gap between my fan and the case; it probably would not be an issue for most people but my printer is in...

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

This will adapt the stock screen mounting to a BTT Pi TFT 43 4.3" Raspberry Pi Touchscreen on the Ender 5 Plus. I run Klipper with Kliperscreen and it works flawlessly. Adapter brackets center and hold the screen where it needs to be. Gives a...

This is for the Ender 5 Plus with linear rails with a Micro Swiss Direct Extruder mounted. To mount the Switch you must thrill 2x M3 screw threads. I hope this Thing is useful for you UPDATE: V2 now available I had Problems with the...

A custom bracket designed to securely house the stock Ender 5 Plus filament sensor following a direct drive upgrade, also incorporating a built-in filament dust filter assembly for enhanced print quality and reduced maintenance. ... The mounting arm...

However, the following text has been rewritten: The Enders 5 Plus bed is connected to a cable that keeps it safe. ...To secure the cable, just snap it into place in the square hole and tie it up with some cable ties, just like you see in this picture.