ender 5 plus mods 3d models

This is a dial indicator mount for the Creality Ender 5 Plus. I didn't originally make this but I modified an existing one I found on Thingiverse from a Creality CR-10. This is an extremely accurate way of leveling your bed. Using this and a good...

I couldn't find any decent hotend cooling setups for the Ender 5 Plus with the Micro Swiss direct Drive extruder plate that didt obstruct view of the nozzle. So I decided to make my own. There are 3 versions that I have created as I have been...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install this...

This is my remix of Satsana, I found this is a really nice project, just needed some tweaks to make it fit better on Ender 5 Plus, corrected the locations to not hit the belts not even the Y axis on the right side. Printing it with 3...

Made this for ender 5 plus to attach cable chain to extruder in a direct drive setup. I could not find anything with key words to find something. So I made it. This is just the brackets to mount cable chain from...

Ender 5 Plus Bowden tube & cable guide =============================== I was frustrated and annoyed because of the inconsistend layer print behavior which lead to bad looking surfaces. I managed to find out, that this was related to the...

I used these to help stabilize the long 2020 extrusions to the 2040 extrusions on my Creality Ender 5 Plus. These can be used on any frame that incorporates the 20 series extrusions. I uploaded multiple variations depending on your preference. There...

Display Mount System for the Ender 5 Plus with Interchangeable Display Mounts. This system utilizes the same display mounts as my All-In-One Stand Alone Case, allowing users to print one mounting system and then easily swap out displays by printing a...

I am currently working on turning my Ender 5 Plus into a high temp filament machine. In that endeavour I realized that I would have to move all my electronics outside the main body so that I can use 1/8" acrylic in the frame as an enclosure. So I...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

Update: - Added a V2, just slightly bigger holes for the bolt and allen key making them easier to fit Purpose: - Liked the original, but like requested in the comments for it, I also wanted M5 fitments - Removed internal filleting and recess -...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

I accidentally printed a Satsana Version for the ender 3, which is identical to the ender 5 x carriage, except for the bltouch. ...It only needs to move about 3mm to the left to clear the fan duct, so rather than printing a entire new shroud, I just...

I accidentally printed a Satsana Version for the ender 3, which is identical to the ender 5 x carriage, except for the bltouch. ...It only needs to move about 3mm to the left to clear the fan duct, so rather than printing a entire new shroud, I just...

Was ask to post my design from :- https://www.reddit.com/r/ender5plus/comments/ljqbks/loving_the_hemera_on_the_ender_5/ They are a little overkill , but if it isn't broke don't fix it .

Ender 5+ Tool holder designed to fit on frame with no screws required. &nbsp;I printed the model as is with no support and 13% infill. ...&nbsp;&nbsp;</p>

The bracket thats been on our wheeled Ender 5 for a while, good printing machine. I recommend $10 pancake motor with it and a firmware current adjustment. ...Chain mount built in GROUP: https://www.facebook.com/groups/541547619887950

Update 8/9/2020 ----------------- The original case bottom design has been renamed "Ender 5 Plus Case Bottom - Creality Mosfet" to indicate it's designed for mounting a Creality Mosfet board. A new version of the case bottom and top have been...

Hallo, habe zwei verschiedene Kabelboxen entworfen, um den Kabelsalat beim Ender 5 Plus dezent zu verstecken. Es gibt in der Box verschiedene Öffnungen. Die 2 Öffnungen die sich im Boden befinden sind für die Z-Achsen Motoren links und...

Hallo, habe zwei verschiedene Kabelboxen entworfen, um den Kabelsalat beim Ender 5 Plus dezent zu verstecken. Es gibt in der Box verschiedene Öffnungen. Die 2 Öffnungen die sich im Boden befinden sind für die Z-Achsen Motoren links und rechts. ...

Cross bar braces for the Creality Ender 5 Plus to stiffen up the frame a bit and lessen the top wobble caused by X and Y axis movement. It reduced the visible wobble quite a lot on my printer. Use any 8mm rod cut to 670mm +/- 5mm for the left...

Totally redesigned my LED bar for the ender 5 Plus. V1 of my LED bar was great, unfortunately since I had printed it with PETG and used LED strips with 5050 LED chips, it warped something fierce. The problem was the LED got too hot for the design....

I converted my Ender 5 Plus Extruder to a Biqu H2 direct drive. I wanted a way to have the filament feed from the top instead of through a bowden tube. I created an offset mount that can hold any filament up to 5kg. I wasn't sure how the filament...

Here is my own design for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with Linear rail. 2 x 5015 component fans, 4010 or 4020 Hotend fan, BL Touch bracket and cable routing to the top. Put the fusion file in here with it, anyone who...

I have upgraded my Ender 5 Plus to a Dual Extruder setup with the Chimera 2in-2out hotend, taking on several requests for files and instructions. Here is my attempt at providing some guidance. Most of these parts are modified versions of something...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

This was the crossbar relocation brackets that stood out to me the most, so I remixed it for the 5 Plus and it works perfectly. The only hitch was not being able to utilize the original tapped holes on one side of the frame - specifically on the 2020...

This is a combination of the Parts from paydayxray (https://www.thingiverse.com/thing:4310609) and Andrea_Botti (https://www.thingiverse.com/thing:4710174) https://youtu.be/n-ky2i-Otvw Ich wollte einen Direkt-Extruder für meinen Ender 5 bauen. Das...

You may think that it's not Ender 5+ any more, but almost everything from the original kit is reused with minimal adjustments.That was the design intention:- no hassle with electronics: 100% ender5+- sturdy frame: I use locally available "Kombi...

Just needed a measuring stick holder for my Ender 5 Pro. The hole is 20mm x 6mm. Should fit for the most types and fits very tight on the 20mm side of the profile. ... I add the Fusion360 file as well.