ender 5 plus linear rail kit 3d models

I was looking around for a kit I could download and print that would allow me to install linear rails on my new Ender5 plus, but the only one's I found were for the CoreXY conversion or with Y rails mounted on the side of the frame instead of on top....

This is a X and Y axis linear rail conversion kit for the Ender 5 Plus with Biqu H2 V2S extruder. It is designed to be durable, low profile and lightweight.A durable and heat-resistant material should be used, PolyMax Polycarbonate is strongly...

remixed to support the microswiss direct drive kit. ...top step has been cut away slightly to clear the microswiss plate.

remixed to support the microswiss direct drive kit. ...top step has been cut away slightly to clear the microswiss plate.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p class="detail-setting printer"><strong>Printer:...

This is a Remix of https://www.thingiverse.com/thing:4892422/. I don't wonted to cut of the parts on the Backside of the Micro Swiss Base, so I expand the carriage. The Nozzle will move -8mm on the Y axe. You have to configure it or to...

To modify the Ender 5 Plus you will need the following: 3x 450mm MGN12H rails 3x MGN12H bearings 66x M3x8mm bolts 66x M3 T-Nuts All the above will cost about $120 or so. Print 2 of the Linear_Rail_Adapter_V3 For the X-Axis you will need M4 and M5...

To upgrade the Ender 5 Plus, you'll need to gather the following essential components: 1. Three 450mm MGN12H rails 2. Three MGN12H bearings 3. Sixty-six M3x8mm bolts 4. Sixty-six M3 T-Nuts The total cost for these parts will be approximately $120. I...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the extrusions....

This is a linear rail mod for the Ender 5 Plus. It encompasses the XY&amp;Z axis. I designed these parts because I was unhappy with most other mod variations of them.</p><p>Z Axis - The Z axis part were designed using the BLV MGN Cube as a starting...

This is a linear rail conversion for the Ender 5 Plus. It encompasses the XY&Z axis. I designed these parts because I was unhappy with most other mod variations of them. <b>Z Axis -</b> The Z axis parts were designed using the BLV MGN Cube as a...

This is a complete overhaul of the ender 5 plus's gantry. After trying the Merc One core-xy mod, I found that the belts were far too long to prevent ringing, and the belt path too complex to avoid problems. Also, the stock belt arrangement really...

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails:...

Was ask to post my design from :- https://www.reddit.com/r/ender5plus/comments/ljqbks/loving_the_hemera_on_the_ender_5/ They are a little overkill , but if it isn't broke don't fix it .

This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't...

... you were homing your z axis then you need to re-level your bed carriage. This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing.

Linear-rails like this can be purchased on Amazon, for example: https://www.amazon.com/gp/product/B078M1GYV4/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1. A short video demonstrating the adapter is available at: https://youtu.be/d2JOcwX44N0. ...An...

For the Y linear rail adapter 4xM4x18mm and 8xM3x8mm For the X linear rail adapter 1xM5x12mm, 1xM5x8mm and 4xM3x8mm 2 x 350mm rails for the sides (Y axis) 1 x 300mm rail for the extruder (X axis) screws + mounting material for the linear rails...

Ender 5 Plus X axis Linear rail with a BMG direct drive. ... Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. ...

Ender 5 Plus X axis Linear rail with a BMG direct drive. Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. Print instructionsCategory: 3D...

For Y axis you'll need 4 - M4x15 bolts (with nuts) and 8 - M3x10 to fix to linear rail block. For X axis you'll need 3 - M4x10 (with nuts) to fix to stock Ender 5 metal plate. 4 - M3x10 to fix to linear rail block. For this mod I used 3 - 450mm...

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...

Hi, i made this Linear Rail Bracket, to get a bit rid of the Z wobble on the Ender 5 Plus This mod doesent change the Print height in any way ! I have 0 improvements on my prints to be honest with you. Maybe with further mods it will make the...

Here is my own construction for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with linear rail. 2 x 5015 component fan, 4010 or 4020 hotend fan, BL Touch bracket and top cable routing. Put the fusion file in here, if you want to...

Hello out there, Here is my project for linear Rail and an EDV6 Volcano on aEnder 5 plus. This mod is huge. At the lateste update , projet works : A few fine tunening are necessary. The improvmenrs a still in progress. Come back regularly here to...

I'm Sick of Long Bowden Tubes and Backordered Hemeras, So I Designed a Direct Drive Mount for My Ender 5 Plus. I'd had it with the lengthy Bowden tube that always seemed to be in my way. Then, when I was ready to upgrade to a Hemera, it went out of...

This is a remix of the linear rail X-Axis conversion kit by SnakeP on thingiverse.It's different in 4 ways:a bit easier to install (comes in two parts - no worries, it's still incredibly strong)the top can hold any upgrade the user would like to...