ender 5 plus klipper 3d models

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

Hello all out there, Here is a big decorative cornet bracket for ender 5 plus printer (or other large printer) I don't know if its useful, but it fill the empty side of the printer. Size 200*200 mm with 50mm clearance. This thing could be used...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

Bretware Ender 5 PLUS Chain System Please subscribe to our Youtube channel https://www.youtube.com/channel/UC-dZpDgCGSf7w-vZWgO2Nsg/videos Uses Johnniewhiskey Ender 3 chain To be used with the following, Chain and covers...

Dan's tutorial and parts can be found here: https://e3d-online.dozuki.com/Guide/Hemera+Creality+Ender+3+(CR-10)+Upgrade./107?lang=en For my Hemera conversion, I utilized the stock Ender 5 Plus Thermistor, Heater, and Fans and purchased a longer...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...

This spacer is specifically designed for users who have installed the BondTech BMG extruder on their Creality Ender 5 plus and still want to utilize the filament run-out sensor. *Update* I initially provided an incorrect spacer, which I promptly...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

Files for Klipper (printer.cfg) as well as the practical addon KAMP (Klipper Adaptive Meshing & Purging) with corresponding instructions as PDF for installation. The printer.cfg is prepared for KAMP and works. The files are exclusively for the...

Gehäuse für das Bigtreetech TFT70 v3 um es an den Ender 5 Plus zu verwenden. Die Bodenplatte habe ich mit 5 Magneten 1x8mm die in die Aussparungen eingeklebt werden befestigt, somit kann man sie jederzeit abnehmen. Man Kann Sie aber auch mit...

This is to mount a Duet 2 Wifi and paneldue in an Ender 5 plus positioned in a way to get maximum Wifi signal. ...you will need to move the mosfet to do this mod, use: https://www.thingiverse.com/thing:4888746 The screen cover and mount is found...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

I got tired of trying to get the whole bed carriage level on my Ender 5 Plus. It tends to sag a little when the power is off, and I struggled to get it back to level every time I powered it on. This simple solution fits on top of the bed frame and...

This clip seamlessly integrates into the extrusion rails of an Ender 5 Plus and likely many other Creality printers, mirroring the ones that come standard with the machine. These clips are clearly designed for wire management, but unfortunately, they...